Hitachi D-1100M belt replacement

Your drive
belt has probably either broken or come off. Make sure your machine is
unplugged and turn it on its side and take the bottom panel off. The belt is in
there. If it has snapped or come off you'll need to replace it. I have a few
belts that might fit. Hopefully your
belt will have letter/number code on the smooth side. It will look something like this: STS 80 S3M 561 Email me that code to [email protected]. If I have it I could sell you the belt. There are several videos
on you tube that show how to put a belt on a bread machine and you could
install it yourself if I have the belt you need.

Get the service manual, order a belt kit from Marrs, then go in and do it.
There are no manuals that give you a step by step process to change belts it becomes intuitive to the Technicians who work on these different units. There are fewer and fewer of them that know what they are doing . There are more and more "technicians" that have no clue about repairing things and charge a lot of money.
I am one of the old timers that have already serviced thousands of decks over 40 years. If you need more help contact me.

Timing belts are typically only used on overhead camshaft engines. Timing belts are used to synchronize the crankshaft with the camshaft, similar to a timing chain on an overhead valve (pushrod) engine. Unlike a timing belt, a timing chain will normally last the life of the engine without needing service or replacement. Timing belts use raised teeth to mesh with sprockets to operate the valvetrain of an overhead camshaft engine.

Whenever a vehicle with an unknown service history comes into your repair facility or is recently purchased, here are some points that should be asked to help prevent costly engine damage:

* Does the owner know if, or when the belt was replaced-
* If the vehicle purchased is used, or the condition and mileage of the last timing belt replacement are unknown, it is recommended to inspect, replace or at least inform the owner that the vehicle is equipped with a timing belt.
* Note the mileage of the vehicle. The average replacement interval for a timing belt is approximately 60,000 miles (96,000 km).


Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.

Removal & Installation

1. Raise and support the vehicle.
2. Remove the engine splash shield.
3. Rotate the drive belt tensioner clockwise to release the drive belt tension.
4. Remove the drive belt from the alternator.
5. Slowly release the drive belt tensioner.
6. Remove the drive belt from the accessory drive pulleys.

Fig. Accessory drive belt routing - 2.4L engines

To install:

1. Install the drive belt to the accessory drive pulley.
2. Rotate the drive belt tensioner clockwise.
3. Install the drive belt to the alternator.
4. Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
5. Slowly release the drive belt tensioner
6. Install the engine splash shield.
7. Lower the vehicle.


Hope helps.

Just replace the drive look on Ebay you can pick one up for under $20. It doesn't have to be the exact model desktop IDE drives are inner-changeable.

need Hitachi HB b201 replacement paddle where can I find this?

It's the belt... you need to replace the belt inside of the DVD drive. It wears out and will be no longer strong enough to pull the hub/motor away from the top magnet so that the tray has space to open. Replacing it with a new belt solves this.

Do you know if you have a Samsung, Hitachi, or other drive in there? This is most common with the Toshiba/Samsung drive and you can find the belt at the following website:

http://store.richspsxparts.com/rebeforxb360.html

your belt number is 726519 and it lists for around 6.28, you can buy it from Hitachipowertools.com or Ereplacementparts.com (ship in 1-2 weeks) I would try Hitachi and also you can find a dealer near you that probably has it in stock, they have a locator on their site. If I have answered your question would you please rate this reply accordingly and thank you.

FOR COMPLETE Diagram Of this Procedure and Belt Routing Email Me@[email protected] and I will Send DETAILED PICTURE and Instructions


NOTE:

• Minor cracks in the V-grooved portion of the serpentine drive belt are considered normal and acceptable. If the drive belt has chunks missing from the ribs, the drive belt should be replaced.
• When installing drive belts on pulley, make sure that all V-grooves make proper contact with accessory pulleys.

Conditions requiring drive belt replacement are excessive wear, rib chunkout, severe glazing, frayed cords, etc. Replace any drive belt that exhibits any of these conditions.

REMOVAL

1. Using a 15 mm socket or wrench attached on drive belt tensioner pulley bolt. Rotate drive belt tensioner clockwise to remove drive belt from pulleys. WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE THAT TOOL DOES NOT SLIP.

INSTALLATION

1. Install drive belt over all accessory pulleys (except drive belt tensioner).Rotate drive belt tensioner as described under Removal to install drive belt over drive belt tensioner pulley. Make sure that all V-grooves make proper contact with pulleys

I have parts for the Hitachi HB B101 Bread Machine

Gates make a drive belt that is the same. Belt number 240J4. I found them for less that $8.00.