20 Most Recent 2007 Harley Davidson FXDL Dyna Low Rider Questions & Answers


Hi, Mark before testing any electrical component in the Turn Signal Light Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, "AGM" batteries fall into this category more so than lead-acid types, also before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced your OEM lights with one or all LED lights you are going to need a load equalizer.
If your turn signal bulb is of the dual element type and the running light portion of your turn signal is not working you may have a faulty bulb, corroded contact, open-short-ground in the running light circuit. A test light and a wiring diagram are your best friends.
If no turn signals are working the cause could be a faulty turn signal module/flasher or the connector going to it, look for, corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion.
If your turn signal comes on but takes several seconds before it starts flashing you may have dirty contacts in the turn signal switch/button, the switch needs to be opened up and cleaned also the flasher may be starting to fail. It should be noted that cold weather will only exacerbate the situation especially when temperatures drop down below freezing and the location of the component, turn signal switches on the handlebar are at the mercy of the oncoming freezing 70 mph wind and makes it hard for the contacts to do their job covered in frozen grease/grime
If all four turn signals flash at the same time like hazard lights even though you only pressed one turn signal button then you have a LED light in the circuit and need a load equalizer that can be purchased from any motorcycle parts supplier.
If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function.
If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction.
If your rear turn signals don't work check your rear fender wiring harness connector first, for corroded, broken, loose pins/sockets, power, and a good ground, the harness connector is usually located under the seat on the front of the rear fender then keep tracing the wiring look for obvious harness damage caused by the rear tire.
If you still can't find the malfunction backtrack from the rear fender wiring harness connector.
If one side does not work you could have a faulty turn signal switch or module check for continuity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
2007 Harley Davidson FXDL Dyna Low Rider wiring diagram Google Search
2007 Harley Dyna Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
Download Manual 2007 Harley Davidson Low Rider Owner Manual
Instant Repair Help over the Phone to speak to me personally $4

2007 Harley... | Answered on Sep 20, 2018


Hi, Terry_montag your bike starts great when cold but once it reaches operating temperature and the engine is shut off for a few minutes then you try to restart it and it will turn over but will not fire or it doesn't do anything, the usual suspects are:
1. When electronics get hot they build up resistance then stop working. It might be an ignition coil, stator, CDI unit etc. First, you must find out if the spark dies out. When the bike won't start, pull a plug wire off, stick a new spark plug in the end and ground the threads on bare metal while someone cranks the engine over. You should see a nice big blue spark between the spark plug gap. Incorrect spark plug gap will cause or contribute to a no start when hot issue.
2. Fuel Tuners have been known to cause this type of problem, disconnect it and see if resolves the issue.
3. Any engine management sensor could be faulty especially the ones that monitor temperature.
4. Gas cap not venting properly, improperly routed fuel lines they must always go down from the gas tank to the carburetor never in any kind of a loop this will cause a vapor lock. Clogged, bent, kinked, pinched or restricted carburetor vent lines will do the same.
5. Overhead camshaft valves adjusted too tight when cold, this will cause loss of compression when hot, except for pushrod engines they usually get looser when hot.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Hard starting when hot
http://kt-trading.net/mcimport/mc/HD/HD.Service.Manual.Dyna.pdf http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://mybikemanuals.com/harley-davidson/007-harley-davidson-owners-manuals
Instant Tech Relief To speak to me personally $6 very cheap

2007 Harley... | Answered on Feb 10, 2018


Hi, Janice your bike does not have cables it has hydraulic brake lines sorry you can not find the first and best tool you ever bought for your Harley despair not, for a mere $10 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below, and for specific information or questions feel free to contact me at xlch@mail.com. Good luck and have a nice day.
BIKER CHOICE Goodridge Front Brake Lines Install
Harley Davidson Manuals Mark Workshop
http://www.stcharlesharleydavidson.com/OEMpartfinder.htm
Owner Manuals Harley Davidson USA
Instant Tech Relief A must have !!! only $ 6 a month cheap

2007 Harley... | Answered on Apr 10, 2016


Hi Oldarmyguy, for more information about your question please visit the website below. Good luck and have nice day.
How to Change the Fork Oil on 2012 Harley Davidson Street Glide Cycles Capacities and Fluid Requirements Fork Filling Quantities

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2007 Harley... | Answered on Jun 11, 2015


Hi Anonymous, for more information about your question please visit the website below. Good luck and have nice day.
Cycles Capacities and Fluid Requirements Fork Filling Quantities

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Harley... | Answered on Jun 11, 2015


Hi Anonymous, for more information on your question please visit the websites below and good luck:
Cycles Capacities and Fluid Requirements Fork Filling Quantities

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Harley... | Answered on May 27, 2015


Hi Curtissiler,on the left side look behind the box like cover that is secured by four nuts. Good luck

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Harley... | Answered on May 14, 2015


Hi Debbie, I know how frustrating these new alarm systems can be, try this website it may be able to help if not get back to me and we will try plan B. https://answers.yahoo.com/question/index qid=20100903124902AAsvdFY
Good luck

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Harley... | Answered on May 11, 2015


Hi Retired Guy,





Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Harley... | Answered on May 04, 2015


Hi Jim, faulty ignition switch. Good luck

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Harley... | Answered on May 03, 2015


Hi Anonymous, go to:

http://www.harley-davidsonforums.com/forums/electrical/32977-finding-resetting-security-codes.html Good luck

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Harley... | Answered on Apr 23, 2015


I kinda wonder if your rear jug plug wire is leaking & grounding it's self.

2007 Harley... | Answered on Jan 03, 2015


Sounds as if your clutch is not releasing enough.

2007 Harley... | Answered on Dec 01, 2014


is it the four way flashers??? How often do they flash??? Do you have tsm or tssm?? Display DTCs and go from there

2007 Harley... | Answered on Oct 18, 2014


COULD be IAC. What DTCs are set?? P0505?? and others??

2007 Harley... | Answered on Oct 18, 2014


Sounds like you have low oil flow problem. Maybe restricted oil filter, or pickup in sump, kinked hose, from oil tank, etc. If you have any other information it would be useful.

2007 Harley... | Answered on Sep 23, 2011


Not trying to be a cop out, but for this particular service, I would buy the service manual, and follow the procedure step by step. This is a safety issue, and done wrong could hurt or god forbid kill you. So step by step.

2007 Harley... | Answered on May 12, 2011


Hi, Robert it should be noted that the reasons your FI light stays on constantly or flashes and your bike will or will not start and may turn over or may not and run great or sputter, these conditions will vary from bike to bike depending on the year, make, and model and you should always refer to your owners/service manual for proper diagnostic procedures. It should also be noted that any type of prior work done to the bike or an abnormal event occurrence IE: adding accessories, electrical curiosity/adventures, laying the bike down/crashes, rain storms/bike washings just before FI light issues started can be significant hints/aids into tracking down the gremlin, also carry the appropriate jumper wire to access fault codes to reduce the risk of being stranded or towed. The newer the bike the more sensitive the ECM becomes and will not let the bike start when aftermarket accessories have been installed without being reprogrammed. That being said the usual suspects are:
1. Faulty Fuel Pump, fuse or system relay switch.
2. Battery starting to fail due to old age/damage, perform a load test.
3. A discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Faulty safety switches/sensors: run/off, ignition, clutch lever, neutral, side stand, tip over, fuel, and or their connections.
5. Broken wire or worn insulation exposing wire to a ground situation especially inside wire harness at tight bends around fairing brackets, under dash panels, under fuel tanks over cylinder heads, etc. Many harnesses are open on the ends that will allow water to enter and accumulate at v-bends.
Dielectric grease and contact cleaner are your best friends for wire/cable/harness connectors, look for corroded, broken, or loose pins/sockets.
6. Installation of aftermarket accessories ie. exhaust systems, mufflers, air cleaners, fuel tuners, electrical component, etc.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
https://www.motorcycle-manual.com/harley-davidson-fault-codes
http://www.mediafire.com/file/3rwutpx50m81jvt/2017_Harley_Dyna_Service_Manual.pdf/file
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
Motorcycle Maintenance Services Harley Davidson USA Free owners manual.
Instant Repair Help over the Phone To speak to me personally $6

Harley Davidson... | Answered on Jul 06, 2019


Hi, Bruce for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
https://www.google.com/search?q=1999+Harley+Davidson+FXDL+Dyna+Low+Rider+fuse+box+location&tbm=isch&source=univ&sa=X&ved=2ahUKEwjpvML-j8vgAhWFna0KHVh1AcsQsAR6BAgAEAE&biw=1440&bih=757
Harley Davidson Dyna Glide Twin Cam 88 Service Manual
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm free owners manual
Instant Repair Help over the Phone To speak to me personally for a mere $6

Harley Davidson... | Answered on Feb 20, 2019


Hi, Billy you may have a dirty throttle cable issue try lubricating with some "DRY SLIDE" for more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Mikuni Throttle slides sticking at wide open position
http://www.transcanimports.com/downloads/Motorcycle%20&%20ATV%20Catalogue/zzzVol%20111/04%20Intake%20Section/Mikuni%202009.pdf
Harley Davidson Dyna Glide Service Manual
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
Safety Recall Information Harley Davidson USA
Instant Tech Relief To speak to me personally $6 very cheap

Harley Davidson... | Answered on Dec 21, 2017

Not finding what you are looking for?
2007 Harley Davidson FXDL Dyna Low Rider Logo

17 questions posted

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Gar
Gar

Level 2 Expert

384 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5914 Answers

Mike

Level 3 Expert

4357 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

FXDL Dyna Low Rider Harley Davidson

  • FXDL Dyna Low Rider Harley Davidson

Most Popular Question

left rear tail light no power signal

  • Motorcycles
Loading...