1999 Honda Accord Logo
Posted on Dec 22, 2010
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Should the center spindle nut and 2 torgued phillip head screws be removed to replace front brake rotor on 1999 honda accord lx

Answer This Question

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Genius:

An expert who has answered 1,000 questions.

  • Master 1,403 Answers
  • Posted on Dec 22, 2010
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Genius:

An expert who has answered 1,000 questions.

Joined: Aug 11, 2010
Answers
1403
Questions
2
Helped
495327
Points
4519

Will try to help. 1st remove the wheel, then remove the 2 caliper bolts that hold the brake caliper on. after removal of brake caliper, [it should just pull off after the 2 bolts are removed] replace the brake pads[be sure to apply anti squeal lube to the outer side of the pads..not the pad itself,the one not contacting the brake rotor] install the pads, the you will need a C clamp to push the brake caliper pistons back into the caliper. i've used this installation easily. use the old pad ,place it against the caliper piston,then apply the C clamp and push the caliper piston back into the brake caliper, then the brake caliper will slide back over the new pads easily, no need to bleed the brakes if you use this solution. replace the brake caliper bolts, then go to next side and repeat the process. after the replacement of the front brake pads,pump the brakes with engine running!!! it's really a simple process. be sure the brake pads are facing the brake rotors with the [pads] facicing the rotors. no metal facing metal. easy! if you have added brake fluid recently, do not be alarmed if you see fluid coming out of the brake master cylinder,when you use the C clamp to collaspe the brake caliper back into the recessed position. [as always when you have to add brake fluid to the brake master cylinder,it only means your brakes are wearing naturally. if you have a vibration in front wheels or steering wheel when braking, you have a brake rotor or both front brake rotors that need replacement with your brakes also. hope this helps and as always, please get a second opinion if you have doubt. an expert will be happy to help. thank you for choosing fixya.com

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Removing the front brake rotor spindle nut
I think when you remove the lug nuts, wheel and
caliper the rotor should pull right off. If its rusted
in place tap it lightly all around. The spindle nut
you speak of might be the hub nut which secures
the drive axle.
Read full answer
Feb 12, 2011 • 1998 Honda Accord
2helpful
1answer

Changing front brake rotor on 1995 honda passport
Put the parking brake On and jack up the front of your SUV.

Remove the lug nuts and you will be able to remove the tire and rimm by sliding them off.Remove the spindle bolt located at the center of the rotor using an 36 mm socket(approx).

Remove the two nuts located behind the rotor (one at top and other at the bottom). This will enable you to remove the brake caliper.While removing it be careful that the caliper tube stays straight.

Slide under your passport and remove the 4 bolts behind the hub using an 12 mm(approx) wrench.Pull the hub assembly out and this will remove the hub rotor in some cases if you are using an tool for pulling the hub assembly out or you have to slide the rotor off the hub assembly.

Slide the new rotor into the hub assembly.Reinstall the brake caliper and make sure the caliper tube is not twisted. Replace the spindle bolt.
Read full answer
Nov 14, 2010 • 1994 Honda Passport
0helpful
1answer

How does one remove rotors on front wheels. Do the 4 bolts have to be removed in order to take off the rotor and do you need a puller in order to do so?
In order to remove the front rotor, you will have to remove the brake calipers first. Get a bungee, a string or wire and use it to support and hang the caliper out of the way. This will prevent excess stress on the brake line. You do not need to remove the 4 lugs, but you do need to remove the 2 Phillips head screws. Be careful not to strip the screw heads, otherwise you will end up having to drill out the heads. Once the screws are out, tap around the edge of the rotor, preferably with a brass or other non-steel hammer, until it comes loose. If it doesn't come loose, application of a good quality penetrating oil around the raised lip near the center can be helpful.

God bless and good luck.
Read full answer
Oct 09, 2010 • 1996 Honda Accord
0helpful
2answers

How do you replace the front rotors on a 1996 honda accord?
Remove wheel. Take off outer driveshaft nut. Remove lower ball joint pinch bolt & separate ball joint from spindle. Pull rotor & spindle out & away to pull driveshaft outer splined end out of rotor center hub. Look on the back of the spindle for the 4 bolts that hold in the wheel bearing. Use a 12 point socket to remove the 4 bolts and remove wheel bearing from spindle (out towards the wheel stud side). Probably will have to use a air chisel to get it out. Once it's out undo the 4 bolts on the outer (wheel stud side) of the rotor and remove the rotor from the hub. Clean & lube the hole where the bearing was in the spindle & the inner face of the hub. MAKE SURE IT'S CLEAN otherwise you may get a pulsation on braking if theres a piece of rust or dirt between the rotor center & the hub face. Reverse procedure to install.

If the rear bolts don't come out then you will have to use a slide hammer to separate the bearing to replace the rotor and there is a very good chance you will need to replace the wheel bearing after you're done (noisy on road test).


Not the job to do at home, usually an easy 2-3 hours per side if things go bad (book time is 2.2 hrs per side). Use good quality rotors as you don't want to have to do it again because a cheap rotor gave you a pulsation.
Read full answer
May 28, 2010 • 1996 Honda Accord
4helpful
2answers

How to remove a rear hub assembly bearing on a 99 honda accord 4 cly 2.3.
acdf6cf.gif



The rear wheel bearing and hub unit are replaced as a unit.
  1. With the vehicle on the ground, loosen the spindle nut.
  2. Raise the vehicle and support it safely.
  3. Remove the rear wheels.
  4. Remove the brake disc retaining screws.
  5. Unbolt the brake hose brackets from the knuckle.
  6. Remove the caliper bracket mounting bolts and hang the caliper out of the way with a piece of wire.
  7. Remove the brake disc. If the disc is frozen on the hub, screw two 8 x 1.25mm bolts evenly into the disc to push it away from the hub.
  8. Remove the spindle nut and pull the hub unit off of the spindle.

Clean the backing plate and the mating surfaces of the brake disc and hub with brake cleaner. Clean the spindle, washer, and hub with solvent.
To install:
  1. Inspect the hub unit for signs of damage or wear. If the bearings are worn, the entire unit must be replaced.
  2. Install the hub unit and spindle washer onto the spindle. Install the spindle nut but do not tighten it.
  3. Install the brake disc and tighten the retaining screws to 7 ft. lbs. (10 Nm).
  4. Install the brake caliper and tighten the mounting bolts to 28 ft. lbs. (39 Nm). Install the brake hose brackets onto the knuckle and tighten the bolts to 16 ft. lbs. (22 Nm).
  5. Install the rear wheels and lower the vehicle.
  6. With the vehicle on the ground, tighten the new spindle nut to 181 ft. lbs. (245 Nm), then stake the nut with a punch.
  7. Tighten the wheel nuts to 80 ft. lbs. (108 Nm).
  8. Test the operation of the brakes.

ADJUSTMENT

The wheel bearings are not adjustable or repairable and should be replaced if found defective.

Thanks for using FixYa!!
Read full answer
Apr 20, 2010 • Honda Accord Cars & Trucks
0helpful
4answers

How do you change the front rotor on a 1997 Honda LX? I have the knuckle out of the car.
Try this:

Read full answer
Apr 01, 2010 • 1997 Honda Civic
0helpful
1answer

How do i replace the back disc brakes on my 2001
There could be a rust buildup in the center surrounding your hub nut making look like the two are connected. Carefully chip the rust away from that area with a hammer and a flat-head screwdriver (wear glasses during). Also the rotor has phillips style retaining screws securing the disc to the hub. If you can't get them screws out I'll tell you what I do on my personal cars, but it's not so approved in the ASE world. I drill the screws out and leave 'em out because the wheel holds the rotor on with the lug nuts. REMOVAL INSTRUCTIONS... Spray some lube in all the openings available on the old disc. You have to remove the bolts to move the brake caliper out of the way (don't open the brake line), just move it and rest it on something like a lower control arm, don't let it hang on a brake line alone. Remove the phillips disc retaining screws. Chip away any rust that is visually preventing removal. OPTION 1 is to insert two 12mm bolts in the threaded holes of the old disc and crank each one evenly until the disc shows signs of backing off (better not to use bolts from the car for this because they can break off in your old disc)... or OPTION 2: Hammer the heck out of it until it can be wiggled off. Rear brakes generally last twice as long as front brakes, this only means they get to sit on there longer and bond to the car as it ages... GOOD LUCK!!!
Read full answer
Oct 01, 2009 • 2001 Honda Accord
0helpful
2answers

How do i remove the rotor for a 1990 honda accord
remove caliper, caliper bracket it may or may not have a screw that holds it to the hub pretty easy actually

hope2help
Read full answer
Apr 05, 2009 • 1990 Honda Accord
1helpful
3answers

Can't take off my front rotors on my Prelude S 1994. There's a large four flange bolt that maybe holding it and I can't take it off.
Look between to of the lug studs and you should see a screw.Remove it and the rotor will slide right off.Stay away from the the center nut unless you are replacing the cv axle
Read full answer
Jan 06, 2009 • 1998 Honda Accord
8helpful
1answer

93 honda accord rotors
Your Accord has what is called "Trapped Rotors". They actually fit behind the hub. The procedure to remove them is not complicated, but it is time consuming.
Here is how I do it:
1) Remove axle retaining nut.
2) Remove brake caliper and bracket.
3) Remove lower ball joint retaining nut and use pickle fork to loosen spindle from lower ball joint.
4) Remove axle from hub.
5) On the back of the spindle, remove four bolts that attach hub/bearing to spindle.
6) Use slide hammer to remove rotor/hub assembly.
7) Remove 4 bolts attaching rotor to hub.
8) While it is a snug fit, the hub bearing does slide through center of rotor to remove it.
Installation is in reverse order.
A bad bearing usually makes a growling noise while driving.
Read full answer
Jun 06, 2008 • 1993 Honda Accord
Not finding what you are looking for?

View Most Popular

1999 Accord

  • Cars & Trucks

Related Question

Removing the front brake rotor spindle nut

  • 1998 Honda Accord

Related Topics

336 views

Ask a Question

Usually answered in minutes!

Popular Questions

Honda radio says ERROR E

2004 Honda Accord

1996 Honda Accord Timing Belt Installation. I need help.

1996 Honda Accord

What does the B1 warning light on Honda Accord

2007 Honda Accord Sedan

2005 Honda accord radio code

2005 Honda Accord

The yellow triangle with an exclamation point is

2004 Honda Accord

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Honda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...