How to reset isuzu digital metere timing belt light on isuzu elf wich is having digital odo meters

• Cliford
• Ignition(key) off press odo button.
• Hold odo switch ignition on for 5 seconds.
• Switch ignition off release odo.
• Press odo, switch ignition on and continue holding until light goes off.
• Switch key off and check by starting vehicle.
• The light should now be off .
• You can also veiw links below.
  • "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
    

Toyota Dyna Landcrusier belt light reset

Toyota Hilux 6th generation BELT Light Reset on Denso Instrument Cluster

How to reset D4D belt light

no year stated, (gee first question in all books is, year)
1959 to present...
then what car (ELF ) then what engine. using real names.
what is the question,?
try to form clear distinct question, please.
so a job stated, cam belt new.
what does check light mean? (the engine check light is unhappy?)
my guess is huge truck ELF.
stick shift manual trans. ok
not gl150 petrol
diesel.
gen 4 ELF 150, is not and engine
its; these.
KAD42/52, TLD23 C240, diesel I4 2369 cc 74 54 3800 Elf 150 Super, Elf 250
the year, and what engine, makes most answers easy.
a cylinder>?
https://en.wikipedia.org/wiki/List_of_Isuzu_engines#G161

here is just a guess at the first ELF150. engine option
there are many more.

Remove the battery cable cables. ( will need radio code to reset) with a ohms meter probe the switch wire and note color find the same color wire at the fuse box and probe if the meter responds the wire is ok . always check fuses with a test light they can look ok and still be open circuit.

if it has a digital odo/ press trip knob until odo is displayed/ press and hold , turn ignition , hold for 4 secounds , release and press again, number 10 will be displayed, keep pressing until 20 comes up, press until odo reading is displayed again, turn ignition off , turn on again , notice the t belt lamp turn off in appros 5 secounds / if not able to reset try this again

Ive never heard of a timing belt light, but there is a maintenance light that can be reset. Here the procedure:

To reset the maintenance reminder light: Turn the ignition switch to the "ON" position. Set the odometer/trip display to the odometer (ODO) mode. Turn the ignition switch off. Depress and hold the trip meter reset button while turning the ignition switch to the on position. The maintenance reminder light will, illuminate for 3 seconds, blink for 2 seconds, illuminate solid for 1 second and then turn off. Release the trip meter reset button. Turn the ignition switch to the off position. Turn the ignition switch to the on position. Confirm that the maintenance light goes out.
Let me know if this helped you out!

this is not right there should be a rubber grommet in cluster lens take out and press button with ignition on to reset light just like resetting trip meter

Look in your owners manual and go to the part that explains the different symbols on your dash. Look for that service reminder and it should tell you what page to go to to learn more about that. Somewhere there should be some wording to the effect that "When you have your car serviced by a certified Toyota dealer they will reset it for you. In the event that someone other does your maintenance then this is the procedure to reset......."

Buzzer Reminder Cancel Mode Setting
1) Set the LCD on the combination meter to the ODO display.
2) Press and hold the TRIP meter reset knob for ten seconds or more within six seconds of turning the
ignition switch to the ON position. Fastening the drivers seat belt while holding the knob cancels the
buzzer reminder.
3) When this occurs, the LCD displays -OFF. The buzzer reminder can be switched between ON and
OFF each time the TRIP meter reset knob is pressed. The LCD displays -ON or -OFF according to the buzzer reminder ON/OFF status. The display changes to the ODO or TRIP meter if the knob
is not pressed for ten seconds.
4) Performing steps 1) and 2) again when the buzzer reminder is off exits cancel mode.
5) The cancel mode will also exit when the battery or combination meter connector is reconnected.

This is really easy! Please follow these directions:

Turn the key ON

Look at the odometer, and verify that it displays "ODO" and the total mileage traveled. If it is on "Trip A" or "Trip B", press the black stick next to the odometer to read "ODO", and the total miles traveled.

Turn the key OFF.

Press in, and HOLD the black trip meter reset button, hold it in.
DO not release it.

Turn the key ON; do NOT start the engine

Observe the Odometer display. The total mileage traveled will disappear, and you will see 5 dashes, then 4, then 3, then 2, then 1 dash, and finally, 5 zeros. Then, the total mileage traveled will redisplay.

Release the black trip meter reset stick.

This completes the reset procedure, and the light will be back on in 5,000 miles, to remind you of you next oil change.

Hope this helps, and thanks for choosing FixYa. Happy Thnkasgiving!

Reset - step 1 turn the key to the 'on' position. using the trip meter button, toggle the lcd until 'ODO' is displayed. step 2 turn the key off. now, push and hold the trip meter button. while holding the trip meter button, turn the key to 'on'. step 3 while you continue to hold the trip meter button, you will see on the lcd disply five (5) small dashes and they will begin to 'count down' rather quickly. step 4 continue holding the trip meter button and once all the dashes have been cleared, your lcd will display six zeros (000000) - release the trip meter button now - and then the lcd will display 'ODO' and your current mileage. at this time, your 'maintenance required'/oil change light has been reset.