Changing front inside door handles - 1990 Toyota Camry

No you don't need any special tool . Find all screws on out side of door trim panel and the window handle , the mirror cover plate , then just pull on edge of the panel .
Gently pry the front side door trim panel (3) from the front side door by disengaging the plastic retainers which secure the panel.
Position the door trim panel (3) away from the door in order to gain access to the front side window switch electrical connector, if equipped.
Disconnect the window switch electrical connector, if equipped.
Remove the door trim panel (3) from the vehicle.
Remove the front side window switch from the door trim panel (3) by releasing the 4 plastic retaining tabs, as needed.

Use a cloth in order to pull off the snap ring which secures the front side door window regulator handle (1), if equipped.
Remove the window regulator handle (1), if equipped.
Remove the front side master window switch, if equipped. Refer to Power Accessory Switch Panel Replacement .

Remove the front side door inside handle (1). Refer to Front Side Door Inside Handle Replacement .
Remove the outside rearview mirror opening cover (2).
Remove the screw which secures the front side door pull handle (4).

Front Side Door Inside Handle Replacement
Removal Procedure
Remove the screw which secures the front side door inside handle (1).
Slide the inside handle (1) forward in order to release the retaining tabs which secure the handle to the door.
Open the front side door inside handle rod retainer and remove the front side door inside handle rod from the inside handle (1).
Remove the inside handle (1) from the vehicle.

Check out youtube video showing how to do it !
How To Remove Install Front Door Panel Suzuki XL 7

Search Results

How To Install Replace Inside Door Handle Chevy Equinox ...

? 9:02
https://www.youtube.com/watch?v=cY6asyM2R6g
Feb 2, 2012 - Uploaded by 1A Auto Parts
How To Install Replace Inside Door Handle Chevy Equinox 05-09 1AAuto.com .... found your tutorial on fixing my driver's side door handle for my 2006 Equinox. .... Door Handles Chevy Equinox 2010 2011 2012 GMC Terrain ...

How To Install Replace Inside Door Handle 2007-13 ...

? 9:05
https://www.youtube.com/watch?v=QonKLwhk2CE
Apr 2, 2015 - Uploaded by 1A Auto Parts
http://www.1aauto.com/interior-door-handle-driver-side-front/i/1adhi00417 1A Auto shows you how to repair, install, fix,change or replace a broken or snappe... ... 10, 11, 12, 13 Chevy Silverado, Tahoe, Suburban and GMC Sierra, Yukon Denali ...2007-2011 Tahoe Yukon Suburban Escalade Vent Section ...Missing: terrain

How To Install Remove Rear Outside Door Handle 2007-13 ...

? 10:02
https://www.youtube.com/watch?v=7ZUTqqEzpZg

can you open from the inside, its the only way you going to get to sort this, failing that you may need to get a new door card and rip the one off the door at the top corner near to the lock latch and split the plastic and pull the door pin inside to open then take the door card off. sometimes you can do it with out braking the door card but would not say it will not brake. inside there is a plastic clip that the handle go's on then another bar to the lock. this is designed to snap if some one trys to open the door with force.failing that the handle part can snap where the bar fits to it. that you would need to change the handle.

Remove front door handle bezel screw cover Remove inside handle bezel screw Remove inside handle bezel Lift upward on the rear of the front door inside handle bezel Disconnect electrical connector Remove handle screw cover
Remove handle screw Remove door trim panel upper screw Remove door trim panel lower screw Remove door trim panel (pull the door trim panel outward to release the pin-type retainers)Remove front door sail panel
Disconnect mirror electrical connector Remove 3 exterior mirror nuts and exterior mirror

unscrew the screw if there is one i can't remember specifically. take a small screwdriver and go above and below the pivot point of the handle to remove the trim around the door handle then the handle itself should push toward the front of the door and then pull out. then the door lock and handle rods should pop right off

the inside door handle is broken, real common. you will need to get that from the dealer, just tell them the year and color. after you remove the door panel. its just a screw and rod to change it.

probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal

1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
   

1. CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
   Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .
   
   
   
   
   

1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
   

1. Pull the shop rag back and forth to release the window regulator handle clip.
   
   
   
   
   

1. Remove the three cover caps and front door trim panel screws.
   

1. Remove the one front door trim panel capped screws from the door pull handle.
   

1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
   

1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
   

1. Remove the front door trim panel.
   

Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal

1. Disconnect the battery ground cable (14301) .
   

1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
   

1. Remove the two front door brace bolts and the front door brace.
   
   
   
   
   

1. Disconnect the front window regulator electric drive electrical connector.
   

1. Remove the four front door window glass regulator track bolts.
   
   
   
   
   

1. Remove the three front window regulator electric drive bolts.
   

1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
   

Installation

1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
   

1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
   

1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.
   

Find and remove two screws visible on the door panel, including underneath small covers. Pop them off with a small screwdriver. Lift front edge of control panel, then pull forward and lift out. Pull upper door panel from door. Disconnect courtesy light connector. Disconnect door open handle cable assembly and door lock cable assembly. You might need to lift panel and twist to get it off.

remove the front door pull cup screw
remove the screw cap and screw from inside handle and slide the handle rearward to disengage the hook from the inner sheet metal. disconnect inside handle from latch remote link if manual windows- remove crank with store bought remover tool. Remove the 2 pushpins from the door trim panel using trim tool pry away door panel [7] fasteners holding panel and push panel in and up . if elect windows disconnect switches

http://autos.groups.yahoo.com/group/villagerquest/

you have to remove the cup behind the door handle. rmove screws aroun the door pull. get a screw driver and pry the trim panel away from the door carefully. There is a plastic christmas tree clip every 6 inches. when the bottom & sides are free, lift up the trim panel to get it out of the track at the base of the window.
--------------------------------------------------------------------------------------

Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).

1. Remove the three cover caps and front door trim panel screws.
   

1. Remove the one front door trim panel capped screw from the door pull handle.
   

1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connections.
   

1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
   

1. Remove the front door trim panel.