Were is the o2 sensor for bank 1 on a 96 grand am 3.1

Check connection to sensor, sounds like you will probley need a new O2 sensor......happens alot

P0171 Fuel trim bank one condition Lean (If bank one and two codes set together suspect fuel pressure or MAF sensor. Or O2 sensor defective
P0174Fuel trim bank two condition Lean (same as above or Failed H02S21 Heated O2 sensor Bank 2 sensor 1)

Hi,
Upstream Oxygen sensor low voltage output bank1. Usually a bad o2 sensor. Bank 1 is cylinders 1-3-5 and upstream sensor usually on exhaust manifold. Replacement is recommended to clear the fault....Mike

160....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)

P0161....O2 Sensor Heater Circuit (Bank 2 Sensor 2)

P0162....O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)

P0163....O2 Sensor Circuit Low Voltage (Bank 2 Sensor 3)

P0164....O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)

P0165....O2 Sensor Circuit Slow Response (Bank 2 Sensor 3)

P0166....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)

P0167....O2 Sensor Heater Circuit (Bank 2 Sensor 3)

P0168....Fuel Temperature Too High

P0169....Incorrect Fuel Composition

P0170....Fuel Trim (Bank 1)

P0171....System too Lean (Bank 1)

P0172....System too Rich (Bank 1)

P0173....Fuel Trim Malfunction (Bank 2)

P0174....System too Lean (Bank 2)

P0175....System too Rich (Bank 2)

P0176....Fuel Composition Sensor Circuit

P0177....Fuel Composition Sensor Circuit Range/Performance

P0178....Fuel Composition Sensor Circuit Low Input

P0179....Fuel Composition Sensor Circuit High Input

P0180....Fuel Temperature Sensor A Circuit

P0181....Fuel Temperature Sensor A Circuit Range/Performance

P0182....Fuel Temperature Sensor A Circuit Low Input

P0183....Fuel Temperature Sensor A Circuit High Input

P0184....Fuel Temperature Sensor A Circuit Intermittent

P0185....Fuel Temperature Sensor B Circuit

P0186....Fuel Temperature Sensor B Circuit Range/Performance

P0187....Fuel Temperature Sensor B Circuit Low Input

P0188....Fuel Temperature Sensor B Circuit High Input

P0189....Fuel Temperature Sensor B Circuit Intermittent

P0190....Fuel Rail Pressure Sensor Circuit

P0191....Fuel Rail Pressure Sensor Circuit Range/Performance

P0192....Fuel Rail Pressure Sensor Circuit Low In put

P0193....Fuel Rail Pressure Sensor Circuit High Input

P0194....Fuel Rail Pressure Sensor Circuit Intermittent

P0195....Engine Oil Temperature Sensor

P0196....Engine Oil Temperature Sensor Range/Performance

P0141....O2 Sensor Heater Circuit (Bank 1 Sensor 2)

P0142....O2 Sensor Circuit Malfunction (Bank 1 Sensor 3)

P0143....O2 Sensor Circuit Low Voltage (Bank 1 Sensor 3)

P0144....O2 Sensor Circuit High Voltage (Bank 1 Sensor 3)

P0145....O2 Sensor Circuit Slow Response (Bank 1 Sensor 3)

P0146....O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 3)

P0147....O2 Sensor Heater Circuit (Bank 1 Sensor 3)

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

Possible O2 sensors:

P2270 O2 Sensor Signal Stuck Lean Bank 1 Sensor 2
P2271 O2 Sensor Signal Stuck Rich Bank 1 Sensor 2
P2272 O2 Sensor Signal Stuck Lean Bank 2 Sensor 2
P2273 O2 Sensor Signal Stuck Rich Bank 2 Sensor 2
P2274 O2 Sensor Signal Stuck Lean Bank 1 Sensor 3
P2275 O2 Sensor Signal Stuck Rich Bank 1 Sensor 3
P2276 O2 Sensor Signal Stuck Lean Bank 2 Sensor 3
P2277 O2 Sensor Signal Stuck Rich Bank 2 Sensor 3
P2278 O2 Sensor Signals Swapped Bank 1 Sensor 3 / Bank 2 Sensor 3
---
This is Bank 1 (closer to the dash panel) Sensor 2 (located after the catalytic converter).

---
Note: A malfunctioning front oxygen sensor may cause fuel trim codes to set.

1. Several Diagnostic Trouble Codes use specific terminology to refer to sensor location. The illustration and key below explain the following terms:
2. Engine BANK Bank 1 is closer to the dash panel, (also referred to as RH or right hand). Bank 2 is closer to the radiator, (also referred to as LH or left hand).
3. UP Refers to Sensor 1 or "front sensor". It is located closer to the exhaust manifold and before the catalytic converter.
4. DOWN Refers to Sensor 2 or "rear sensor." It is located after the catalytic converter.
5. The following examples show how to interpret oxygen sensor terminology:
6. B1/S1 = Bank 1/Sensor 1 = Dash panel side, BEFORE the catalyst or "upstream"
7. B2/S2 = Bank 2/Sensor 2 = Radiator side, AFTER the catalyst or "downstream"

Grand Cherokee oxygen sensor locations for 4.0 and 4.7 engines







Four wires (circuits) are used on each O2 sensor:

• 12–volt feed circuit for the sensor heating element
• Ground circuit for the heater element
• Low-noise sensor return circuit to the PCM
• Input circuit from the sensor back to the PCM to detect sensor operation

O2S Sensor removal Never apply any type of grease to the oxygen sensor electrical connector, or attempt any soldering of the sensor wiring harness.
WARNING: THE EXHAUST MANIFOLD, EXHAUST PIPES AND CATALYTIC CONVERTER(S) BECOME VERY HOT DURING ENGINE OPERATION. ALLOW ENGINE TO COOL BEFORE REMOVING OXYGEN SENSOR.
1. Raise and support vehicle.
2. Disconnect O2S pigtail harness from main wiring harness.
3. If equipped, disconnect sensor wire harness mounting clips from engine or body.
CAUTION: When disconnecting sensor electrical connector, do not pull directly on wire going into sensor.
4. Remove O2S sensor with an oxygen sensor removal and installation tool.

02S Sensor installation
Threads of new oxygen sensors are factory coated with anti-seize compound to aid in removal. DO NOT add any additional anti-seize compound to threads of a new oxygen sensor.
1. Install O2S sensor. Tighten to 22 ft. lbs. (30 N·m) torque.
2. Connect O2S sensor wire connector to main wiring harness.
3. If equipped, connect sensor wire harness mounting clips to engine or body. When Equipped: The O2S pigtail harness must be clipped and/or bolted back to their original positions on engine or body to prevent mechanical damage to wiring.


Hope thats help (remember comment and rated this).

Standing in front of the car looking at the engine bank 1 is the cylinders on the front of the engine. These are cylinders 1-3-5. On the rear is bank 2 cylinders 2-4-6. The O2 sensor is located screwed into the exhaust manifold or the exhaust pipe on the front of the engine.

BANK 1 SENSOR 1 IS THE ONE IN THE EXHAUST MANIFOLD. BANK 2 SENSOR 2 IS BELOW THE CATALYTIC CONVERTER.

P0171 SHOULD GO AWAY WITH A GOOD O2 SENSOR BUT DO CHECK FOR VACUUM LEAKS TO BE SURE. 3.1/3.4L ENGINES HAVE A BAD DESIGN INTAKE MANIFOLD GASKET, THE LEAK OIL, COOLANT, AND AIR.

Bank 1 is the frt side exhaust manifold (did they say bank 1 sensor 1?),you can start by replacing that sensor,i would check the intake for leaks ,the gm 6cly. are known for bad intake gaskets,you will see oil coming out form the frt or rear of the intake,also check your atifreeze overflow bottle for bronwish sludge,which means that the oil is mixing with the antifreeze.A leaking intake could cause that lean condition.