Where is the canister purge valve located on my 2013 hynudia veloster

Evaporative Emission Canister Purge Solenoid Valve Replacement
Removal Procedure
Remove the air cleaner assembly from the studs and reposition to the side.
Disconnect the evaporative emission (EVAP) canister purge valve electrical connector (1).
Disconnect the EVAP canister purge valve tube from the intake manifold. Refer to Plastic Collar Quick Connect Fitting Service.
Disconnect the chassis EVAP vapor line from the EVAP canister purge valve. Refer to Plastic Collar Quick Connect Fitting Service.
Remove the EVAP canister purge valve bracket bolt.
Remove the EVAP canister purge valve with bracket.
Remove the EVAP canister purge valve from the bracket.
Inspect for carbon release in the EVAP canister purge valve ports. If there is any loose carbon, replace the EVAP canister and any components necessary to remove the carbon particles.
Installation Procedure
Install the EVAP canister purge valve to the bracket.
Position the EVAP canister purge valve with bracket to the cylinder head.
Caution: Refer to Fastener Caution.
Install the EVAP canister purge valve bracket bolt.
Tighten:
Tighten the bolt to 18 [n-m] (13 lb ft).
Connect the EVAP canister purge valve tube to the intake manifold. Refer to Plastic Collar Quick Connect Fitting Service.
Connect the chassis EVAP vapor line to the EVAP canister purge valve. Refer to Plastic Collar Quick Connect Fitting Service.
Connect the EVAP canister purge valve electrical connector (1).
Position the air cleaner assembly and install onto the studs.

The Evaporative Emission (EVAP) Canister Purge Solenoid Valve is located in the EVAP canister, above the rear of the muffler. The Evaporative Emission (EVAP)Canister Purge Solenoid Valve is located in the EVAP canister, above the rear of the muffler.

You have put two parts on your list. The purge valve is by the engine and the charcoal canister is by the fuel tank. What was the code you got?

The purge control valve is located near the vapor control canister and that is under the car near the gas tank.

Mar 16, 2014 - 2 posts - ‎1 author
I have a 2003 Vue 3.0L 2wd.After fueling I have trouble starting, it cranks but I have to pump it a couple of time then it starts, Sometimes after it ... 2008 Saturn Vue Purge valve canister solenoid location ...
9 posts
Aug 24, 2013
access to vent valve solenoid - SaturnFans.com Forums
2 posts
Jan 20, 2013
Service engine soon light: P0440 - SaturnFans.com Forums
6 posts
Apr 15, 2010
Code P0446 (evap solenoid) and now I can't fill the gas ...
16 posts
Nov 17, 2007
More results from www.saturnfans.com

EVAP Solenoid Location - YouTube

? 2:17
https://www.youtube.com/watch?v=jIKaPF2Yw3I
Mar 20, 2007 - Uploaded by richpin06a
Saturn EVAP Solenoid Location. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by CarsNToys ...

EVAP Purge Solenoid Removal - YouTube

The canister purge valve is on the intake manifold . The vent valve is under the vehicle near the fuel tank .
The vent valves opens and sends exess gas fumes to the purge valve witch in turn opens when the engine is running faster and can burn this excess fuel Its all about emissitions

There is a canister purge valve & a volume control purge valve on your truck. The canister purge valve is on the evap. canister itself(at the rear of veh. near the fuel tank. The volume control purge valve is located in the eng. compartment, passenger side behind Battery. You didn't mention if it's a 4 or 6 cyl.

The 98 model uses a square canister located under the left rear quarter panel.
There is a canister purge control valve and a canister volume control valve, so make sure you are dealing with the right valve.
The volume control valve should be on or near the intake manifold, and the purge control valve should be near the canister.

Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine

1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
2. Disconnect the vacuum pipe from the EVAP canister purge valve.
3. Disconnect the purge pipe from the EVAP canister purge valve.
4. Remove the EVAP canister purge valve and bracket.
5. Remove the EVAP canister purge valve from the purge bracket.
6. Inspect for carbon release in the EVAP canister purge valve ports.
   

To install:

1. Install the EVAP canister purge valve on to the purge bracket.
2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
3. Connect the purge pipe to the EVAP canister purge valve.
4. Connect the vacuum pipe to the EVAP canister purge valve.
5. Connect the EVAP canister purge valve harness connector.
6. Remove the air cleaner outlet resonator.
7. Disconnect the EVAP canister purge valve harness connector.
8. Disconnect the engine purge pipe from the EVAP canister purge valve.
9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
11. Remove the EVAP canister purge valve along with the mounting bracket.
12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines

1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
2. Remove the rear purge pipe from the EVAP canister purge valve.
   NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
   
3. Disconnect the EVAP canister purge valve electrical connector.
4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
6. Remove the bracket.
   

To install:

1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
3. Connect the EVAP canister purge valve electrical connector.
4. Connect the rear purge pipe to the EVAP canister purge valve.
5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines

1. Raise the vehicle
2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
3. Remove the hose from the EVAP canister vent valve.
4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
5. Remove the clip from the EVAP canister vent valve harness connector
6. Disconnect the EVAP canister vent valve harness connector.
   

To install:

1. Connect the EVAP canister vent valve harness connector
2. Install the clip into the EVAP canister vent valve harness connector.
3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
4. Lubricate the hose end with lubricant.
5. Install the hose to the EVAP canister vent valve.
6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
7. Lower the vehicle.

Hope this help (remember commetn and rated this).