Question about 1994 Volvo 940

Open Question

<!-- from fixya rte -->Alt. pully nut right or left hand thread - 1994 Volvo 940

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 91 Answers

SOURCE: 1992 Volvo 740 Wagon w/o Turbo: Timing Belt Needs Replaced

It is a right hand thread and you usually need an impact gun. Take the fan out of the way, to give you more room, I have found that helps.

Posted on Apr 10, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Is the near side rear brake hub nut left or right hand thread on 2008 Suzuki swift 1.5 thanks'


Most hub nuts are usually standard thread but they can be fitted to a ridiculously high torque setting. This means they can be a ******* to get off. The torque is somewhere around 175Nm, (130ft lbs).
The last hub nut I had to deal with needed a seriously heavy duty breaker bar. A high range torque gun can also be effective.

May 29, 2018 | Suzuki Cars & Trucks

1 Answer

How do I replace the inner tie rods?


undo the ball joints at the steering arms , loosen off the lock nuts just enough to unscrew the rods
Right hand side right hand thread , left side left hand thread
If you do not move the lock nut back more than 1 thread then you set the lock nut in the same place on the new rod , you will not need a wheel alignment
If you have to take the lock nuts off to fit to the new rods , measure the distance from the end of the rod to the face of the lock nut and position the lock nut at that distance on the new rods

Jan 13, 2016 | Cars & Trucks

1 Answer

99 sable crank pully nut


It's a bolt, and if left hand threads, it will be the first time I have heard of such. No pin would be through the threads. Try the breaker bar or impact gun the other way. If engine tries to turn, pull the starter and wedge a block of wood against the ring gear teeth on the flywheel.
Don't know about sables, but thought all crank bolts were regular threads.

Dec 28, 2012 | Cars & Trucks

1 Answer

I`m changing the water pump in my 1999 dodge ram 1500, but I can`t lose the fan nut that is attach to the water pump.please help.


Those fan nuts are just tough to get off, however it may have "left-hand" threads. If you can see any threads, look straight down at them...if threads are going "downhill" from right to left, then they are common right-hand threads, Lefty lucy-Righty tighty. However if the threads are going "downhill" from left to right, then they are left-hand threads, and you will need to turn the nut "clockwise" to loosen it. Hope this helps....let me know either way!!

Aug 12, 2011 | 1999 Dodge Ram

1 Answer

27060-17040 IS THE PULLY NUT LEFT OR RIGHT HAND THREAD


It should loosen the opposite way that the belt spins it.

Apr 12, 2011 | Toyota Land Cruiser Cars & Trucks

2 Answers

We r strugeling to remove the crankshaft pully and we now un shaw if its a left or right hand thread??


it is a regular thread but you almost need an impact wrench to remove bacause they put them on tight at the factory

Feb 14, 2011 | 1984 Jeep CJ7

1 Answer

Is the crank pully left or right hand thread


It should be a right hand thread, if you put a breaker bar on the bolt and touch the starter, the bolt should come loose. Make sure the bar is up against something solid on the right hand side of the car, not the radiator hose, or your hand. Hope this helps.

Jun 20, 2010 | 1987 Toyota MR2

1 Answer

Change altrnator belt on a 1999 chrysler 300. I got the belt on but i need to know how to make it fit, is there some kind of adjusstment


there is a pully to the bottom left of alt losen nut in center of pully then there is a bolt turn it an the pully will move get belt on an adj don"t forget to tighten nut on pully

Apr 05, 2010 | 1999 Chrysler 300M

1 Answer

I need to replace the harmonic balance seal.


THE thread is a std Left hand to undo But you will need a 3/4 drive100 lbs air rattle gun to both undo and redo up the bolt on front pully.. BUT there is another way and that is as you say a big breaker bar and a good socket, but you will have to take off the starter motor and put a good fitting bar into the starter ring teeth and turn it to the top and dont let it slip out of the teeth and once locked into place gently put pressure on and undo the bolt..
But its unusual for the seal to leak on its own as its mostly due to either the front pully has worn a grove in it or the crankshaft bearing is also worn, so check the front pully for wear first. Ron

Nov 23, 2009 | 2005 Ford Futura

2 Answers

How can I remove the spindle nut? It seems to be


itll come just use a bigger diameter hose and higher pressure. You can use alil heat if your replaceing the hub and bearing but i still wouldnt recommend it.

Jul 17, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
1994 Volvo 940 Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...