Question about Cars & Trucks
No crank , the horn blows when you turn the key to crank the engine. The drivers door latch has gone bad and has been replaced. The problem started when the old door latch malfunctioned and you couldn't open the door from the inside or outside.
The truck has a feature, where you turn the key in door lock , the alarm should stop going off. there is a small switch on back of the lock cylinder. it may have popped off and is in lock position, but you cant turn it back to on position, because it popped off from the back of the lock. remove the door panel and look inside of the door where the lock is. make sure, that the switch is attached firmly to the back of the lock cylinder. start there.
Posted on Jul 04, 2013
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
jimmy: it sounds like the drivers door unlock tamper switch or the other switch may have failed. One side can affect the other under certain circumstances. Your trunk lock also has a switch which arms and disarms the antitheft system. Try locking all the doors, make sure the hood and trunk lid are closed and then open the trunk. Leave it open open the drivers door and try to start the car.
If it's a no start. Disconnect the ground battery cable then put the ignition key in the run position in you ignition switch. Reconnect the battery and try to start the car. It should start. This usually will override the anti theft system. One issue with this will be, whether the antitheft system will remain disarmed.
Although I have never tried this before, I know that the system will not arm unless all the doors, trunk and the hood are closed.
I could suggest this to try if the car starts as I had told you pertaining to disconnecting the battery cable, I would take the switch and unbolt it from the passenger's side of the engine compartment just forward of the shock tower. Just let it sit somewhere so it doesn't get caught up in anything moving. If there is a light under the hood of your car, remove the bulb.
Let me know how you make out.
Posted on May 03, 2009
YOUR WIRELESS CONTROL MODULE(SENTRY KEY MODULE)MAY BE ELECTRICALLY LOCKED UP..THERE IS A SERVICE BULLETIN FROM CHRYSLER..YOU CAN REMOVE IOD FUSE IN FUSEBLOCK(UNDERHOOD BEHIND AIR CLEANER..IGNITION OFF DRAW(IOD)THIS WILL RESET WIRELESS CONTROL MODULE AND VEHICLE SHOULD START AND LOCKS RESPOND AGAIN..IF IT DOES,THE WCM WILL HAVE TO BE REPLACED AND THIS NEEDS TO BE DONE BY DEALER
Posted on Jun 14, 2009
Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.
Posted on Jul 18, 2009
Start with fuel system. Listen for fuel pump humm at fuel tank No humm check wiring to pump for power. Then check for spark at plugs and wires. Remove wire from coil and hold near engine and see arch when you crank. No arch. Replace ignition Modular inside distributor cap or cap or rotor
Posted on Feb 04, 2010
Tips for a great answer:
Oct 13, 2018 | Lexus Cars & Trucks
Jul 15, 2018 | Honda Cars & Trucks
Oct 31, 2015 | Cars & Trucks
Sep 08, 2017 | Honda CRV Cars & Trucks
Jun 27, 2012 | 2000 Chevrolet Tahoe
Apr 30, 2011 | 1999 Plymouth Voyager
Dec 03, 2010 | 2000 Ford Taurus
Mar 09, 2017 | 2000 Chevrolet Blazer
Jan 05, 2018 | 2006 Toyota Corolla
Jul 18, 2009 | 1995 Jeep Grand Cherokee
94 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: