- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
It should be in the vicinity of the armrest....Is this a door armrest or center console armrest? In either case, the adjustment will be near to the armrest, like the seats have an adjustment at the hinge area.
Position the seats as needed to remove the console.
Disconnect the battery. For additional information, refer to Section 414-01 .
Remove the floor console storage bin.
Remove the 3 screws and the armrest.
Remove the floor console storage bin screw.
Remove the pin-type retainer.
Disonnect the electrical connectors.
Remove the floor console front finish panel.
Pull upward from the front of the trim panel to release the retainers.
Disconnect the electrical connectors.
Remove the floor console center finish panel.
If necessary, remove the 2 screws and the floor console cup holder.
Remove the 2 floor console front screws.
Remove the 3 floor console rear screws.
To install, tighten to 4 Nm (35 lb-in).
NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
Remove the 2 screws under the armrest door that hold shifter trim. The front of the trim will just pop up since it's clipped in. There will be some wires for the ash tray light, you to unplug. There are some 10mm bolts inside the armrest, as well as 1 on each side near the front of the console.. If I remember correctly, been awhile. go slow and good luck.
I am assuming you are talking about the front center armrest here. You have to start by removing the back cover of the center console along with the vent louvres if equipped. I think this will expose two screws that you need to remove and the armrest will pull out. If you are trying to remove the armrest because the latching mechanism has gotten out of sync, you can fix that in the car. If that's the case let me know and I'll try to walk you through the repair process.
there are about 8 torx screws (very small) near the hinge of the lid. remove those and the lid will come to remove the entire console, there are bolts on the back of theconsole accesible from back seat, and on the side of the console. easiest way to acces those bolts would be to remove the front two seats. they are held in by two bolts in front and two nuts under plastic covers in the back. raise the emergency brake lever and the console will slide up and be removed.
Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
Lift the floor console from the front and rear console panel mounting brackets.
Base Console, Floor, Ranger, Explorer
Removal and Installation
Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
Lift the floor console from the front and rear console panel mounting brackets.
×