Question about 2008 Chevrolet Malibu

2 Answers

Windshield wipers don't move, but hear motor running

Posted by on

  • Anonymous Mar 14, 2014

    2002 f150and I can hear the wiper motor working but thewiper blades do not move

  • Lukd
    Lukd Feb 09, 2019

    I don't understand what to do how to fix

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 5 Answers

Check the nuts on the wiper arms and make sure they are tight. If the nuts are tight then a linkage on the wiper transmission probably came loose or broke. You'll have to pull some cowling off to access it.

Posted on Apr 22, 2012

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I used a lighter to temporarily fix the issue until I could get a grommet in the mail- pulled linkage and motor out and heated up the bad grommet the stuck it on the boll socket. Then used needle nose pliers to form it some (back around the ball) while still warm.... though it was 10 degrees out.

Posted on Jan 05, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

SOURCE: why isnt my windshield wiper working?

Easy fix. Very very common chevy issue. the wiper motor goes but no wipers, or they work one time and not the next. drove me nuts for two years. It is the wiper control module. The board actually get moisture in it cracks the sod-er joints they are there go get magnifying glass. hair line cracks in the board. how ever good new auto zone advance auto who ever carries the board 30 bucks. located back of the fire wall by the wiper motor. three torx screws. remove torx. care full not to bend prongs when pulling board. replace with new screws and cover and board. seal new cover with silicon rtv so forth to re prevent moisture. when it rains, rain drops on this board by the top crack and will reoccur. but this is sure fix. did my truck and my buddies. Make sure to use silicon or don't waste your time. Been good ever since 1 year now.

Mike

Posted on Feb 03, 2009

  • 701 Answers

SOURCE: wheres the circuit board for a windshield wiper

Hello jlwhelchel: My name is Roger and I will answer your question. Raise the hood locate the wiper motor. Remove the cover held on by three screws. Remove the cover. The cover is the module.
Should you need further help please just ask. Please rate the answer. This way I know the information was helpful. Thank You for using Fix Ya. Roger

Posted on Oct 16, 2009

emissionwiz
  • 85206 Answers

SOURCE: Timing Venture wipers

disconnect the wiper transmission from the motor, then run the motor and turn the motor off with the wiper switch, this will park the motor, re-attach the wiper trans linkage so the wipers are parked/down

Posted on Dec 05, 2008

  • 65 Answers

SOURCE: My rear windshield wiper stopped working on my

My 2005 tahoe did the same thing. I also bought a new motor, which did not fix. I discovered there was a bad ground. Instead of searching for bad ground, just install a short length of stranded wire with crimp terminals between a wiper motor mounting bolt and a rear glass latch assy mounting bolt to restore good grounding to the wiper motor.

Posted on May 10, 2010

  • 166 Answers

SOURCE: On a chevy venture one windshield wiper is moving

Well, having just dealt with this on our 2000 Lesabre... this is an unfortunate fate for windshield wiper setups...
Basically the knurling on both the male & female portions of the wiper arm's pivot point have worn clean off, or are very close to gone.
----
The following solution is my 'get it working now' fix... it's not as official and/or costly as replacing the whole wiper linkage... not to mention how difficult it may be in pulling apart the necessary components to first get at the wiper linkage, and then actually removing it from the vehicle(serious pain on some vehicles)... and then of course installing a new one, assuming you can even find/afford one through the local stealership.
----
What I did, which has worked so far:
First, get access to the nut which holds the wiper arm to the pivoting point; there should be a cover or cap which will remove to expose this nut I talking about. Be sure the wiper arm is in a position that you want it in... then tighten that thing(the nut) if it's not already tight - a relative "really tight" is recommended, but do stop short of jumping on the ratchet or wrench. To verify tightness, check that wiper arm for wobble, i.e. semi-gently move/pivot it in all sorts of directions, to see whether it is actually sitting tight up against the pivoting stud that you just tightened the nut down against. I've seen the female/upper part of the wiper body lift & shift around which makes tightening things a bit of a fine tuning process until you manage to get the wiper body low & seated fully onto the pivoting stud part.
The next part is to more surely "bond" the wiper arm to the stud that it pivots on(and causes it to pivot too). Just make certain the wiper arm is tightened down in the position you want it to be(low/at-rest alike to the other wiper on the windshield) before proceeding
You'll very likely need a super hard drill bit to have success in drilling through the portion of the wiper arm that sits around the pivot-point/stud and into the stud itself some distance.
I'd suggest an 1/8" carbide drill bit(likely not available at your local hardware store, and I don't recall if anything less-hard will work to drill
that stud) acquirable via Use-Enco.com
Once a hole is drilled through the outer wiper arm metal(sometimes even as soft as aluminum, but regularly mild steel), and a good ways into the very hard pivoting stud material, get yourself an 1/8" diameter roll-pin/friction-pin in the 1/2" to 5/8" range and tap/hammer it into your newly made drill-hole. The roll/friction pin is designed to fit tight inside of an 1/8" hole so you won't find it coming out on its own(unless you didn't drill the hole deep enough, or wobbled the drill bit while drilling thus making the hole larger than 1/8").
Roll-pins, like wipers, are typically black so not much should be seen from any casual glance or typical once-over of the vehicle.
The fix should turn out to be(in every ideal sense) an easily disappearing, effective long term fix.
I hope that goes well for you.

Posted on Jan 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My windshield wipers wont work.


It Sounds Like, Either The Arms Are Loose ,If You Can Hear Something Moving Behind The Dash,
Or The Linkages Are Seized ,If The Motor Just Hums No Movement Heard,In Which Case Try Spraying Q 20 On The Linkage And Try Moving The Wiper Arms By Hand To Get It Going Again,
If Not The Motor May Just Be Burn;t Out.

Mar 16, 2013 | Cars & Trucks

1 Answer

WINDSHIELD WIPER CLUTCH/TRANSMISSION ALIGNMENT


one of the arms under the firewall came off look down through where wiper motor is

Feb 26, 2018 | 2002 Saturn Sl

1 Answer

REPAIR WINDSHIELD WIPER CONNECTION TO MOTOR..MOTOR IS STILL RUNNING BUT WIPERS WILL NOT MOVE


The teeth or the screw that hold the wiper arm is strip.
Check and replace.

Mai Lor

Feb 24, 2013 | 2002 Saturn S-Series

1 Answer

2004 tundra windshield wipers don't move but motor runs


If both wiper arms move, the linkage between them probably is OK. What isn't OK is the connection between the arms and the motor. You will have to get access to the motor area to find out what needs repair

Dec 27, 2012 | 2004 Toyota Tundra SR5

1 Answer

Tengo un stratus 99 que esta fallando el sistema electrico


The windshield wipers don't work at all or you can hear the motor running but the wiper arms do not move?

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Jul 29, 2012 | 1999 Dodge Stratus

1 Answer

Windshield wiper doesn't work


If both wipers don't move, could be the switch or the wiper motor.

Jul 02, 2012 | 2000 Pontiac Montana

1 Answer

The windshield wipers to my Ford focus stopped working today. They worked for a little while & then stopped in the up position. You can hear the motor working but they don't move. You can move them...


Your wiper linkage has come off the wiper motor. To reconnect the linkage, first remove the wiped arms, the remove the wiped cowl. The wiper cowl bolts are located under the hood and screws through the spaces in the cowl. Reconnect linkage, reinstall cowl, reinstall wiped arms.

Jul 05, 2011 | 2006 Ford Focus

1 Answer

The windshield wipers on my Chevy Blazer 97 stopped working,just makes a sound, but not moving? What do I need to check/replace?


Sounds like the windshield wiper motor needs to be replaced. The gear inside may be stripped so you'll hear it running but it won't do anything. I've had that happen with the rear wiper motor. Hope that helps.

Jun 15, 2010 | 1997 Chevrolet Blazer

2 Answers

Front wipers stopped working but you can hear the motor run also


If the wipers were buried under snow/ice or frozen to the windshield, you may have blown the red 10 amp fuse located in cavity 9 in the fuse block located on the bottom left side of the instrument panel near the parking brake pedal.
In order of easiest to check:
1) ensure wipers not frozen to windshield.
2) ensure wiper arms are not loose on the pivot stud,
3) check the red 10 amp fuse.
You stated that "you can hear the motor". Which motor do you hear? The engine or the wiper motor?
If you hear the wiper motor, then the fuse is alright. Try 1) and 2) above.
PT Stanley

Jan 20, 2009 | 1998 Dodge Grand Caravan

Not finding what you are looking for?
2008 Chevrolet Malibu Logo

24,144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...