20 Most Recent
2006 Hyundai Accent - Page 8 Questions & Answers
I have a 2006 hyundai accent
No one could tell me what was wrong with my 2006 hyundai . Why the check engine light kept being on. Autozone, Napa, Advance auto, their FREE diagnostic machine could not figure the problem.It kept reading p0012 and they didn't know what exactly that meant so... I had to give in and take it to the hyundai dealership and pay$99 for a real diagnostic test. That's when I was told it was my oil control valve and the problem got fixed, no more headache!
Ihave a 2006 hyndai accent
No check engine light means there is something wrong with engine, get it checked. Your Dad is also right but that light is "Service" light or specific part light like in toyota the clutch change light appears after some defined kilometers and it has to be reset after clutch change (it does not go off itself as there is no feature to detect new clutch etc).
I need to know what the spark plug gap setting
2006 Hyundai Accent Gl 1.6 L4 C FI
STANDARD BKR5ES-11 GAP 044
V-POWER BRK5E-11 '' ''
G-POWER BKR5EGP ''
LASER PLATINUM PFR5N-11 ''
OE LASER IRIDIUM IFR5E-11 ''
IRIDIUM IX BKR5EIX-11 ''
DO NOT TRY AND GAP THE PLATINUM OR IRIDIUM TYPE.
I hope this engine is the same for you,if not let me know the engine code.
Service pollen filter diy
Open your glove box then undo the little tie straps holding up your glove box. Once it falls down further, the door to your cabin filter is exposed. Just pinch the ends on either side of the narrow door, and you should be able to pop it off, then just slide the filter out.
Reverse procedure to put everything back together. Good luck!
The interior lights dont come on when I open the
More likely the switch striker on door is broken, unplugged, out of adjustment, or corroded--check those 4 things--then check if wire from front door post to door isn't broken--you have to open the harnass & first find the correct wire To fix it.
When must be replaced tla distribution belt
If you are referring to the timing belt, it should be replaced every 75-80k miles.
If you are referring to the serpentine belt, they should be inspected every oil change, look for cracks on the inside of the belt, this will indicate the belt is worn and needs replacing.
My hyundai 2006 bonnet does not open you have to
You need to lubricate your hood latch assembly. WD-40 works well for this. Spray some on and work the latch back and forth a few times with a screwdriver blade. Spray a little more on, and close the hood and see if it opens any better. You may have to repeat a couple times to get good results.
My hyundai 2006 bonnet
All in all ... not all that unusual. Get spray, white, lithium grease and lube the hood (ops ... bonnet) catch mechanism.and spray some liquid lubricant on the operating cable.
I think this will help you a lot if not eliminate the problem all together.
The eps light came on and the power steering
I have a 2006 Accent and also to me sometimes the eps light turn on while I'm driving. I turn off the car and wait few seconds before to turn on again. But how to repair this problem?
Check engine light is flashing
If its on solid, you need to scan it soon. If its flashing it means its urgent & u need to pull over & turn off the engine!
2006 accent ,we put key
Read your owners manual on how to re-set the alarm off as when you locked the doors you have used the remote key and used regular key to open the door. As you alarm system a bit different than the one I have, you may have to press different remote button sequence to re-set the alarm and get the immobiliser re-set to off. Normally the engine should re-start after 15 minutes rest between tries with alarm re-settingsequence.
The way mine works, I have to turn on and off the ignition without starting engine then after 3 turns it should chirp then I would turn it fully to start the engine.
If you find this helpful, please return a thumb up and a favourable vote resposne. Thank you.
My daughters hyundai accent 2000
Do the blinkers work? If the same bulbs work as brake lights also work as blinkers, the wires for them are routed through the turn signal switch. If that switch is bad, you won't have brake lights.
Not finding what you are looking for?