20 Most Recent 2006 Chrysler Sebring Questions & Answers


There is no need to loosen the transmission mounts bolt to get the clearance needed to change the back plugs. There are two plastic nuts that holds the upper insulation in the back engine wall. Remove them and fold the insulation under and you will get the clearance needed to remove all three back plugs.

2006 Chrysler... | Answered on May 06, 2019


I take help from online websites that have this service like helping in repair some like reliable- store have instant help.. others are a bit slow which I don't prefer... rest is up to u.. U can also get free manuals

2006 Chrysler... | Answered on Feb 16, 2019


Do you mean the PCM (power Control Module) ? If you do, after installing it it will have to be programed at a Chrysler dealer to match up with your car. Vin, year, odometer reading must be programed into it to match your car.

2006 Chrysler... | Answered on Oct 08, 2018


Expansion valves are ALWAYS located at the inlet of the evaporator coil

2006 Chrysler... | Answered on May 19, 2018


Probably a bad clockspring a device in the steering wheel that control the airbag. Have abs system scanned for codes.

2006 Chrysler... | Answered on Feb 12, 2018


Cv axle assembly inner and outer constant velocity joint

2006 Chrysler... | Answered on Jan 03, 2018


id try the relay first. its cheaper. should be in fusebox under the hood

2006 Chrysler... | Answered on Nov 28, 2017


If it happens, you can just disconnect the fuse for the horn, or relay. It could be the switch underneat the airbag or clockspring.

2006 Chrysler... | Answered on Nov 19, 2017


Remove the keys, close all doors, trunk, hood, etc. Push the lock button twice if you have a remote, press the unlock button twice if you have the remote. If no remote use the key for the drivers door; turn it to the right two times. Meaning rotate right, back to center, rotate right, and back to center. Then rotate left two time in the same sequence as above. Open the door, ensure the vehicle is SECURELY in the PARK position and give it a go. It may be helpful to put your foot on the brake and shift through the gears a time or two prior to attempting to start. If that works, please let me know! Good luck!

2006 Chrysler... | Answered on Oct 01, 2017


Another thought is bbbind.com has diagrams.
Some libraries carry automotive databases with wiring diagrams and repair info. One of their databases you can access on your home computer for free, if you live in an area they serve. It's not the best, but, better than nothing. You know what they say, you pay for what you get.

2006 Chrysler... | Answered on Sep 26, 2017


This code can also be caused by a thermostat that failed open. Is the engine heating up normally or taking longer than usual? Are there any symptoms? Did they run tests on the sensor? Personally, I perfer mechanics that confirm the fault before replacing parts. Too many of them do that. Be thankful that yours doesn't.

2006 Chrysler... | Answered on Jun 25, 2017


Check for fuses or fused link, also check for voltage regulators, Chrysler uses an integrated power management system that is under the fuse panel in the engine compartment.

2006 Chrysler... | Answered on Apr 01, 2017


Take the car to a local Autozone and have the Alternator tested, it is free. Also when the "Battery" light comes on it doesn't mean there is a problem with the battery persay it means the battery is not getting charged up while you drive.

2006 Chrysler... | Answered on Mar 28, 2017

Not finding what you are looking for?

728 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sebring Chrysler

  • Sebring Chrysler

Most Popular Question

expansion valve 06 chry sebring conv

  • Cars & Trucks
Loading...