Top 10 1992 Ford Crown Victoria Questions & Answers

Cars & Trucks Logo

Question

  • 10,059 People Helped

location of EGR valve for 4.6 liter engine

location of EGR valve for 4.6 liter engine? how do you remove the EGR valve?

Posted by on

Answer

  • Most Helpful of 3 Answers

a887903.gif
EGR VALVE IS #2.

Please wait for second post to answer your second question....comes with a few pictures.

Posted on Nov 16, 2009

Question

  • 5,253 People Helped

How to replace egr valve on 1995 crown vic 4.6.

How to replace egr valve on 1995 crown vic 4.6. Valve is in hard place to get to.

Posted by on

Answer

  • Most Helpful of 1 Answers

On 1995 Crown Victoria the EGR valve is located at the rear of the engine compartment. While the attaching bolts can be gotten out with a little bit of a problem the egr tube that atteches the EGR valve to the right exhaust manifold is a pain. It is possible to do though. Here are the removal and installation instructions. If you are sure that the EGR valve is the reason for any check engine light then you can remove the battery cable for about five minutes to reset the light, but if the light is on for a differant reason then you just got rid of the code plus any freeze frame data that a shop could have used to diagnose the problem.

Check this procedure about REMOVAL & INSTALLATION...

PFED Sensor
See Figures 9, 10, 11 and 12


bcc2045.jpg
Fig. 9: Detach the connector for the DPFE sensor


78e8250.jpg
Fig. 10: Matchmark and remove the vacuum hoses for the DPFE sensor and ...


daae4e4.jpg
Fig. 11: ... remove the retaining nuts from the DPFE sensor and ...


b6fd561.jpg
Fig. 12: ... remove the DPFE sensor from the intake manifold

  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring harness from the DPFE sensor.
  3. Label and disconnect the vacuum hoses.
  4. Remove the mounting screws and remove the DPFE sensor.
To install:
  1. Position the DPFE sensor and tighten the mounting screws.
  2. Attach all necessary hoses and wiring to the sensor.
  3. Connect the negative battery cable.

EGR Valve Control Solenoid
See Figures 13 through 17


bb3e162.jpg
Fig. 13: Detach the connector for the EVR solenoid


a9fc1b4.jpg
Fig. 14: Match mark the vacuum hoses for the EVR solenoid and ...


57ba344.jpg
Fig. 15: ... remove the vacuum hoses from the EVR solenoid


f5d5cc2.jpg
Fig. 16: Remove the retaining nut for the solenoid and ...


4b98f79.jpg
Fig. 17: ... remove the solenoid from the intake manifold
  1. Disconnect the negative battery cable.
  2. Label and detach the vacuum hoses from the EVR solenoid.
  3. Detach the electrical connector from the solenoid.
  4. Remove the retaining hardware, and remove the solenoid.
To install:
  1. Position the solenoid and install the retaining hardware.
  2. Attach the main emission vacuum control connector and the wiring harness connector to the EVR solenoid.
  3. Connect the negative battery cable.

continue...

Posted on Jul 16, 2010

Question

  • 1,636 People Helped

1992 crown victoria fuse box diagram.I don't have the cover for a inside fuse box.Pease help.

1992 crown victoria fuse box diagram.I don't have the cover for a inside fuse box.Pease help.

Posted by on

Question

  • 963 People Helped

transmission only goes in reverse

transmission only goes in reverse

Posted by on

Answer

  • Most Helpful of 2 Answers

Most likely the forward gear has broken that means you need a rebuild or a new transmission ......But thats my opinion I had the same thing happen to me and most of the time it works only in reverse that means the forward gear has broken....Hope this helps and sorry for the bad news....

Posted on Nov 19, 2009

Question

  • 841 People Helped

Speedometer runs but odometer dont; on 1993 Crown Victoria

i can see the speed in dial , the needle moves but stops onece in long while. But the odometer never changes a number. i tried zeroing the distance measure several time but it dont work it is all zeros all the time. Any help would be greatly appreciated..

Posted by on

Answer

  • Most Helpful of 1 Answers

Sounds like the speedometer head itself has failed or is in the process of doing so. While it may be possible to obtain just a speedometer head it would be far easier and probably cheaper to go down to the local salvage yard and get yourself a whole new instrument cluster. Many times they will come with instructions for resetting the mileage to match your car, if it doesn't, just attach a drill to the connection point for the speedometer cable and run the drill until it has the right mileage.

Posted on Oct 10, 2009

Question

  • 799 People Helped

1992 Crown Vic wont crank

New battery. Won't start (even with a jump) - *no click*. Headlights, radio, heater all work.

Posted by on

Answer

  • Most Helpful of 3 Answers

Check the starter solenoid. Usually mounted on a fender well. Find by following the + battery cable.

Posted on Feb 14, 2009

Question

  • 699 People Helped

ford transmission not shifting

my 1992 ford crown victoria won't shift into overdrive. changed the transmission with a used one that I knew worked properly, but once installed in my car same problem occurred, the trans slips when attempting to shift.

Posted by on

Answer

  • Most Helpful of 1 Answers

i think you got a bad transmission...thats what it sounds like anyway

Posted on Jan 12, 2009

Question

  • 670 People Helped

1992 crown vic 4.6l

1992 crown victoria wont start, battery ok, starter ok, just wont start no crank just tick

Posted by on

Answer

  • Most Helpful of 2 Answers

did you check the inertia switch?? that's what happened to mine

Posted on Aug 13, 2008

Question

  • 663 People Helped

my key won't turn in the ignition, steering wheel

my key won't turn in the ignition, steering wheel is locked up

Posted by on

Answer

  • Most Helpful of 1 Answers

Try turning the wheel in both directions with some force while turning the ignition. Sometimes the steering wheel is in a bind when the vehicle is parked and it makes the ignition lock cylinder "stick". WHen you relieve the pressure on the steering column you should be able to turn the key.

Posted on Oct 03, 2010

Question

  • 641 People Helped

I need a diagram to see how to repair the power

I need a diagram to see how to repair the power motor window in the passenger door's window. The window will not stay up.

Posted by on

Answer

  • Most Helpful of 1 Answers

its not the motor, its the window regulator... good luck finding diagrams- take the door panel off and start drilling the rivets out.

Posted on Jul 14, 2009

371 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

1992 Ford Crown Victoria Crown Victoria

  • 1992 Ford Crown Victoria Crown Victoria

Most Popular Question

automatic transmission 1992 crown

  • Cars & Trucks
Loading...