20 Most Recent 2009 Toyota Camry LE Questions & Answers

Torque them in sequence to 52 ft lbs and then mark the front of them and turn 90 degrees (start from the inside out working from one side to the other)

un do the bolts that hold the seat belt rewinder take out the back seat and then undo the bolt that holds seat belt to floor of car then install whole replacement seat belt unit inset and retighten the bolts. http://www.carparts.com/toyota/camry/seat-belt

Front lower strut/ shock mount 155 ft/lbs. Rear lower strut/ shock mount 133 ft/lbs.

It sounds like the lock connecting rod is loose or the servo is not working. Does the passenger side door open with the key? If it does, the connecting rod is OK, but the servo will still be no 1 suspect.

Try writing in english sentences please. If the a/c and heat don't Want to come on then they must not be inate objects. and therefore must have feelings and emotions. So try talking to the heating and air conditioning units in a soothing tone of voice. try coaxing them to come on with penut butter and jelly sanwiches or some other treat.

You are not supposed to release this gas to atmosphere. Best to take it to a car A/C shop, it is not expensive.

Hi Chickgamerr, There is a micro switch fitted under the cushion of the seat and another in the buckle part of the seat belt. To get to the switch under the seat will mean removing the seat, which requires the two bolts at the front of the rail and the two at the rear being removed together with the electrical connector being disconnected. Lift the seat out and turn it upside down. The problem may be there or with the buckle switch, which may be frozen. Spray a little WD 40 into it and plug in and release the buckle a number of times to free it up. Refit everything and safe motoring. Regards John

It can have an optional alarm system, yes.

The ABS light being on is most likely the wheel speed sensor, the wheel speed sensor is still 100% good, it's just that someone didn't remove the sensor before working on the strut, so when they pushed down on the lower control arm or knuckle they ripped the 20-24 Gauge wire apart, you can buy a new harness or splice it back together and use heat shrink to hold it.

Get a test light see if its the fuse blown i swap its fuse or relay with another one just to see if thats the problem if not its ur open shut switch itself

wire color code? https://eautorepair.net/Marketing/Default.asp read

plz I need Toyota 1G FE ECU Pinout Diagram thanx

Have you checked the speed sensor on the transmission ?

Hi there,

As you have not stated the vehicle MODEL or Year of Manufacture, I will provide a 'general' solution:

There could be numerous causes for high fuel consumption, but if you have used this amount of fuel in such a short journey, there would have to be leaking fuel somewhere.

However, the only true method to measure "ACTUAL" fuel consumption (disregard trip computer) is:

- Completely fill tank to a pre-determined point inside the fuel tank filler tube.
- Set your cluster Trip Meter to: 0000
- Drive vehicle for 6 - 15km and return back to the same gas station pump used previously.
- Completely fill tank to the same point inside the fuel tank filler tube, where filled previously.
- Note the quantity of litres required to fill to that same point in the filler tube.
- Divide the litres used, by the total Km travelled on your Trip Meter.
- If the value calculates less than 20 (carburettor engine); less than 15 (EFI engine), then consumption is acceptable.

Note: if value is above these numbers, then you have a fuel leak, or a problem with your vehicle's carburettor adjustment. EFI engines can have numerous causes, including electronic sensor faults etc.

Cheers,

Question edited for clarity. Question moved from MISC to Toyota Camry. After replacing the sensors, the code needs to be cleared with a scan tool. What Does the P0038 Code Mean? Diagnostic trouble code (DTC) P0038 stands for "HO2S Heater Control Circuit High (Bank 1 Sensor 2)". Oxygen sensors evaluate the amount of oxygen in the exhaust gas and send their readings to the powertrain control module (PCM).Oct 15, 2021

P0038: Heated Oxygen Sensor Heater Control Circuit High ...

https://www.google.com/search?q=Toyota+Camry+P0038 ..

Question edited for clarity, 'maker'. Also need the year. All questions need 'year make model as first three words in every question please. Question moved to model category. https://www.google.com/search?q=Toyota+Camry.+How+to+replace+A%2FC+fuse+(type+B) ..

Yes. Vacuum lines control alot of different functions. They control fuel pressure ' vent the engine fumes, air intake valve, valves for the a/c and more. Open leaks can cause high idle speed and cylinder missfire. https://video.search.yahoo.com/search/video;_ylt=AwrhcTpaerJiXzIRfzGJzbkF?p=2005+camry+3.0+vacuum+line+diagrams+2005+honda+3+5+liter&type=E211US1494G0&fr=mcafee&fr2=p%3As%2Cv%3Ai%2Cm%3Apivot#id=1&vid=d315ed55566f4bf7cb76e7ac7a3c8a78&action=view