Whirlpool Ovens - Page 4 - Recent Questions, Troubleshooting & Support


try Cutting power to unit at breaker box for 5 minutes. This may reset electronics

Whirlpool Ovens | Answered on Nov 21, 2018


SAFETY THERMOSTAT MAY HAVE TRIPPED. MOST ARE LOCATED BEHIND THE REAR SERVICE PANEL. THERE SHOULD BE A WIRE DIAGRAM, USUALLY ON TOP OF THE OVEN IN A POCKET, IF THE THERMO IS OPEN, WILL HAVE TO BE REPLACED & OVEN WOULD HAVE TO BE CHECKED FOR ACURACY.

Whirlpool Ovens | Answered on Nov 13, 2018


were I you I would forget it has that feature as MANY times it causes the heating element to burn out there in costing you even more money to repair that

Whirlpool Ovens | Answered on Nov 10, 2018


Unfortunately, the F1E1 error indicates a EEPROM checksum problem with the control board. An internal check for the board gave a result that didn't match the one that is stored in the read-only memory. The only solution is to replace the electronic control board for the stove.

Please add a comment with the model number of the stove if you would like to know if this control board is still available and the price for it.

Cindy Wells

Whirlpool Ovens | Answered on Nov 05, 2018


It should be spelled out in your owners manual.

Whirlpool Ovens | Answered on Nov 04, 2018


When the power drops, it often sends a spike down the power line. Most electronics are sensitive to voltage spikes and if too high, destroys the equipment. Unfortunately your display is probably toast.

Whirlpool Ovens | Answered on Nov 02, 2018


LED clock/temperature light fading an - Appliance Repair Forum

forum.appliancepartspros.com/oven...ranges.../650-led-clock-temperatur...

Aug 20, 2007 - 3 posts - ‎3 authors
The LED clock/temperature/etc control light has been becoming less ... needs to be replaced (board being the oven clock/erc/control board). Control pad temperature light out
2 posts
Jun 15, 2014
Dim temp lights
2 posts
Feb 7, 2014
Frigidaire range LED display is dim
10 posts
Aug 28, 2009
Oven clock & light
1 post
Jun 21, 2009
More results from forum.appliancepartspros.com

Cheap Fix for a Dim Display on an Oven Control Panel ...


Whirlpool 30"... | Answered on Oct 30, 2018


Try asking the store about it. Maybe it's a privacy setting you need to turn on(or off)

Whirlpool Ovens | Answered on Oct 25, 2018


I had similar issue with my electric stove as well. The model of the stove is the same as the one that us mentioned above on the beginning of the this discussion. The issue I had on my stove was that the display shows time and no error code how ever the oven top light indicator comes on but the oven won't heat up. Here are the steps I took to fix the issue: First I unplugged the stove and used a multimeter to verify that it has 240Volt coming. It checked good for 240v. Second, I opened up the terminal on the stove where the plug connects, there I discovered one of the hot leg has melted and broken thus only 120v getting to the stove. I repaired the broken wire and verified 240v coming in the stove and stove was fixed for good. I further investigated what caused the wire to melt and broken, my finding was exposed hot wire shorted to the stove body (ground). Hope this helps. Thanks for reading
10_5_2018_1_34_33_pm.jpg

Whirlpool Ovens | Answered on Oct 05, 2018

Not finding what you are looking for?
Whirlpool Logo

3,579 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Ovens Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...