Panasonic Audio Players & Recorders - Page 6 - Recent Questions, Troubleshooting & Support

i have a panasonic SA-HT720 and it displayed locked anytime i wanted to eject discs so i found out that dad27's solution was the best and holding down the stop and power buttons also locks the system as well as unlocking it. God richly bless u dad27 u really helped me out

Cannot eject disc. ≥The unit may have a problem. While the unit is off, press and hold (>> / >>I) and (< OPEN/CLOSE) on the main unit at the same time for about 5 seconds. Remove the disc . After disc removal or if this does not work you may need to reset to factory defaults. for the player alone.

To return all settings other than some settings to the factory preset.

≥Select “Yes” in “Restore Default Settings” in the Setup menu.

This returns all values in the Setup menu and the on-screen menu, except for “Remote Control Code”, “On-screen Language”, “IP Address/DNS Settings”, “Proxy Server Settings”, “Network Service”, “DVD-Video Ratings” and

“BD-Video Ratings” to the default settings.

If this does not work then you may need to reset everything to the factory settings.

To return to the factory preset. Everything Reset.
(No setting)

≥Reset the unit as follows:

1 Press [POWER] on the unit to turn off the unit.

2 Press and hold (>> / >>I) and press [POWER] and [< OPEN/CLOSE] on the unit at the same time for more than 5 seconds until “PLEASE WAIT” is displayed on the unit.

3 The power is turned on and then turned off automatically.

Cheers!

The SA-AK57 is the center of the SC-AK57 mini stereo home theater system. The included speakers have color coded wiring for the front speakers. One speaker connects to the red and black terminals on the SA-AK57; the other speaker connects to the blue and grey terminals. Push on the top of the terminal levers and insert the bare copper wire into the opening. Then release the lever. The center, right and left speakers use a single RCA or banana-plug connection and plug straight into the jacks on the SA-AK57. Panasonic has the manual for the SC-AK57 on the product page: https://shop.panasonic.com/support-only/SC-AK57.html . The current link to the manual is ftp://ftp.panasonic.com/audio/om/sc-ak57_en_om.pdf . See page 7 for the speaker wiring. I hope this helps. Cindy Wells

F70 interrmintent problem caused by (Ic-current) interupted, supply for cpu, Q1702 (emitter point) high resistant to IC1701, suggestion- connect a wire between these component due to pcb track poor contact.

have a look for all swollen caps and replace as needed for a start

Replace the laser assembly.

http://www.hifi-remote.com/codes-amp.shtml But better to buy a facsimile remote for your model, an exact copy! https://www.ebay.com/itm/Replacement-Remote-for-TECHNICS-SAGX330-RAKSA303P-SAG9013P-SAGX130-/111089776701 https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk02_4O6eLuVa5S4BwiPDarR4kVv6-A%3A1611115680170&ei=oKwHYJ_gCaKs5NoPx6GR2Ac&q=Technics+SA-GX130+replacement+remote ..

Try this website for an online copy of the manual. https://www.manualslib.com/products/Panasonic-Sapt480-Dvd-Home-Theater-Sound-System-2754226.html

Turning a wired speaker into a wireless speaker would be difficult and disproportionately expensive. Each amplifier channel will need a transmitter and each speaker a receiver, a preamplifier and power amplifier and a power source capable of supplying the whole for a reasonable time before recharging. If you choose wireless (radio) to transmit to each speaker the frequencies will have to be adjusted so they don't conflict. If the speakers are to be used within sight of the base then infrared transmitters and receivers could be the answer, similar to that used with some of the early wireless headphones.

You will have to disassemble the unit to gain access for removal.

1. Open internal fuse 2. Power supply failure

Possibly because components in the amplifier chains have been overstressed and consequently failed. The output stages are frequently affected by high gain levels.

https://www.google.com/search?q=replacement+Panasonic+SC+pm-01+remote ..

It it worked before, you need the amplifier servicing. You have blown components by overloading it.

Possibly a blown channel causing it to enter safe mode or Wait mode.

Is the display not working completely? If it is working, What error code are you getting on display?

The drive must have a pin-hole in front. Use a needle/pin in that hole and press it. It may help to unlock the tray. Give that a try.

Como quitar bloqueo del teatro panasoni modelo sht730

Hi i have penasonic vk90d after i service the unit . The unit is stuck on dvd but nothing works dvd tape fm aux nothing work the unit is stuck on dvd changer. Any body help me plz
[email protected].

No but you can buy another cable and join it together to rich the length that you need