There are vertical stripes when something is printed.

Vertical colored stripes on your V555-G1 TV can be caused by a few different things. The first thing you should check is the cable that connects your TV to the input source.

Make sure that the cable is firmly connected to both the TV and the input source. If the cable is firmly connected and you're still seeing vertical stripes, the next thing to check is the settings on your TV.

Make sure that the resolution is set to 1080p and that the refresh rate is set to 60Hz. If you're still seeing vertical stripes, try changing the HDMI input that your TV is connected to.

If you're still seeing vertical stripes after trying all of the above, it's possible that there is a problem with your TV. You can try resetting the TV to see if that fixes the problem.

If the problem persists, you may need to contact customer support for further assistance.
Will replacing the T-con board help?
The short answer is: maybe.
The longer answer is that it depends on what is causing the problem in the first place. If the problem is with the T-con board, then replacing it may well fix the issue.

However, if the problem is with something else - like the LCD panel itself - then replacing the T-con board is not going to help.

1. Open the Printers folder.
   
   
   • For Windows XP Select 'Start', 'Control Panel', 'Printers and Other Hardware', and 'Printers and Faxes'.
   • For Windows versions other than Windows XP select 'Start', 'Settings', and 'Printers'.
   
   
2. Right-click the printer icon to open Properties.
   
   
   
   
3. Click the 'Maintenance' tab and click the 'Print Head Alignment' icon.
   
   
   
   
4. The message below is displayed. After confirming the two points below, click 'Print Head Alignment'.
   
   
   
   
5. The following message is displayed. Click 'OK'. Print head cleaning starts. The power lamp flashes during cleaning operation. Do not perform other operations. After cleaning has finished, the first head alignment pattern will be printed.
   
   
   
   
6. The following message is displayed. After printing has finished, click 'Yes'.
   
   
   
   
7. Refer to the printed sheet, and select the pattern with the fewest visible vertical stripes in column A.
   
   
   
   
   
   <1> Example of highly visible vertical stripes in the pattern.
   <2> Example of the fewest visible vertical stripes in the pattern.
   
   
8. Enter the selected pattern's number in the Column A box.
   
   
   
   
9. Similarly, enter the selected numbers in the boxes for column B to F.
   
   
10. After all numbers have been entered, click 'OK'.

Yes absolutely the PCU problem, contact your nearest shop to check the PCU before anything will happen to your printer.

Please rate me solved you decide to check the PCU. Don't look for another solution because I got already the right answer which already suspected at your own guest.


Best regards,

Philip

hello
you have to check the fuser film, it may be not good

regerds and dont forget to rate mt answer

You may have some dust on the imaging window (printer head). Remove the toner cartridges and clean it with some tissues.

It sounds like the black drum unit needs to be replaced.

remove PC drum and under that you can see laser glass, clean it and reinstall.

Select the Jet Substitution Mode.

1. On the Control Panel, select Troubleshooting, and then press the OK button.
   
2. Select Print Quality Problems, and then press the OK button.
   
3. Select Eliminate Light Stripes, and then press the OK button.
   
4. Select Jet Substitution Mode, and then press the OK button.
   
5. Follow the Control Panel prompts to select the color and malfunctioning jet number indicated on the Light Stripes Test page.
   

see if this solution fixes the problem.
Also clean the print head using instructions in the manual
http://www.fixya.com/support/t241840-smudges_color_printing_black_ok

If the blank stripes go up and down the page (vertical) then it sounds like the laser lens has simply got toner on it. remove the toner and photo conductor units. Look for the glass panel that covers the laser lens and simply wipe it off with a cloth. Some machines incorporate a lens wiping pad that can clean the lens without taking out the parts. I can not remember if the 1710 does or not.