Question about Bench Grinders

Open Question

Nutool bench grinder/sander is it possible to get a manual for this machine it is a NTG6L-4.

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 2712 Answers

SOURCE: Bench Grinders Safety issues

Goggles or safety glasses need to be worn to protect the operator's eyes from the sparks and metal filings that result. Depending on the workpiece and time of exposure, hearing protection may also be required, the dust produced is also potentially hazardous. The toolrest (or workrest) should be mounted slightly below the center of the grinding wheel with less than 3 mm clearance from the wheel. This prevents the work from jamming between the toolrest and the wheel. Grinding wheels designed for steel should not be used for grinding softer metals, like aluminium. The soft metal gets lodged in the pores of the wheel and expand with the heat of grinding. This can dislodge pieces of the grinding wheel. Wire brushes require particular attention for the safety of the operator and bystanders as the metal wires may become dangerous projectiles as they could bind with the object being brushed and so throw it away with great energy. The machine needs to be securely mounted to a pillar or a bench to be used safely and effectively, often with an emergency stop switch or pedal fitted close by the machine, for use in emergencies.

Posted on Aug 27, 2008

Ad

marionbagget

  • 718 Answers

SOURCE: switch and capacitor crapped out on 1/2 hp Sears bench grinder

Replacement should be simple. Just do a one for one hookup with the new part, after you unplug it first.
For a diagram go to;

http://www.searspartsdirect.com/partsdirect/getSubComp.pd?modelNumber=397.1949&productCategoryId=0721000&brandId=0247&modelName=CRAFTSMAN-1%2F2-H.P.-GRINDER&diagramPageId=00001&documentId=00023041&pop=flush

Posted on Mar 28, 2009

Fred Yearian

  • 5603 Answers

SOURCE: bench grinder, 110/220?? wired up properly

LIKELY the capacitor which is usually in the base is bad.

The capacitor shifts the phase angle in one of the two windings which creates a pseudo rotating field to start rotation.

Posted on Nov 16, 2009

Marvin Thornbrue

  • 172 Answers

SOURCE: Need part numbers to replace eyeshields on Dayton bench grinder

Your grinder is listed on page 3085 of the Grainger catalogue. The part number for the eyeshield is 00281.00 and the number for the lower eyeshield bracket is 00280.00. The right hand upper eyeshield bracket is number 25188.00 and the upper left hand bracket number is 25177.00. All of this can be ordered through Grainger at 1-800-323-0620. Marvin T.

Posted on Jan 13, 2010

Testimonial: "This was very helpful. I have ordered parts from Grainger. Thank You."

rowdy45176

David Ford

  • 2176 Answers

SOURCE: I am looking for a Dayton Bench Grinder Manual

I would try and call Grainger parts to see if they have one. I know they deal with and sell Dayton equiptment. If no luck let me know and I will try and find another source.

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I purchase eye piece for nutool NTG6L grinder/sander


says not to Canada. May be good for you?

Nutool (2) - Nutool

nutool.pl/gb/1_nutool?&p=2List of products by manufacturer Nutool ... Dust collection bag , easy sanding belt replacement , continuous running ... Bench Grinder NUTOOL 150W/150mm.

other suppliers
nutool NTG6L spares Google Search

Apr 23, 2017 | Tools & Hardware - Others

2 Answers

How do I operate bench grinder?


A murphy, A bench grinder must be used with a lot of caution and respect while using this equipment, Check the attached links,instruction and guides, Good luck work safe.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

OSH Answers Fact Sheets

Pedestal Bench Grinder Safety

Bench Grinder Basics

Mar 21, 2016 | Bench Grinders

1 Answer

I have a very old Nutool NTG6L which is a combined grinder and 2" belt sander. Is it still possible to buy new sanding belts for this machine or is it too old?


I suggest doing a search on eBay. Depending on where you live, you may need to find them in another country. A Google search might help first but I found these on eBay Ireland.
2 Pack Of 3 Sanding Belts Nutool Nu Tool NTG6L 6130 Bench Sander

Nov 29, 2014 | Tools & Hardware - Others

1 Answer

Is the 4A912B Dayton 10" 1 HP bench grinder 3 phase or 1 phase?


If the plug on the cord has 2 flat prongs and one round one then its 110 VAC single phase. If the motor has 4 wires then I'd suspect 3 phase. The data plate on the motor will tell you for sure.

Nov 19, 2014 | Bench Grinders

1 Answer

I need instuction manual for a Milwaukee sander/grinder


go to milwaukeetool.com and you can download the owners manual, you will need the serial number to ensure that you get the right one. Let me know if you need more assistance

Sep 23, 2011 | Milwaukee 6140 6 4 1/2in. Sander/Grinder

1 Answer

I have an Abbott & Ashby 200mm Industrial Bench Grinder - CS-8GCM I need to change the sanding belt and am unsure how to do it, can you help?


Remove/open cover on the right side of belt assembly housing. push downward on tracking knob left side top of unit.Belt is spring tensioned to remove slack.Push down remove old belt,push down again for new belt.With belt running adjust belt track(centering) by turning knob,top of unit,toward or away from you,Arrow on inside of new belt governs direction of rotation of belt.

Jun 09, 2010 | Sander 6" Bench Grinder 2" Belt Combo...

1 Answer

Looking for belt length for older bench sander model # 28643


Try contacting: trugrit.com
suipergrit.com
klingspor.com
If not in standard inventory,these sites can customise,in all types of abrasives and grits.

Dec 08, 2009 | Craftsman Grinders

1 Answer

On the Bench Oscillating Spindle Sander how do you lock the spindle so that you can remove the bolt at the top to change the sanding sleeve? When I try to loosen the bolt the spindle turns and I don't have...


Remove the spindle from the machine itself before you change the sanding sleeve. There should be a flat section on the bottom of each spindle that you can hook a wrench on to hold it while you undo the top bolt.

Mar 09, 2009 | Delta Machinery ShopMaster SA350K Bench...

1 Answer

USING MY DELTA #17-960 SCILLATING SANDER FOR THE FIRST TIME IN A LONG TIME. NO USER'S MANUAL.


OK you will have to contact a Dewalt Service Center, They do not have that manual online at this time. If there is still a problem and you cant locate let me know and I will try something else. I found a breakdown at Ereplacementparts.com but no user manual

Jan 01, 2009 | Delta Machinery ShopMaster SA350K Bench...

Not finding what you are looking for?
Grinders Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bench Grinders Experts

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2010 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Are you a Bench Grinder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...