WorkCentre 7835 not booting, how to troubleshoot or do factory reset

1. Hard Reset or Factory Reset: Try performing a hard reset or factory reset on your device. This process typically involves holding down specific buttons for a certain period or accessing a reset option in the device settings. Be aware that a factory reset may erase your data, but it could help resolve the boot loop issue.
2. Connect with Support: Reach out to Bushnell customer support directly. They may have specific instructions for troubleshooting a boot loop issue. Provide them with as much information as possible about the problem, including any error messages you may have encountered.
3. Check for Firmware Updates: Ensure that your device's firmware is up to date. If there are any available updates, install them as they may include bug fixes that address boot-related issues.
4. Battery Status: Ensure that the battery is charged and functioning properly. Sometimes boot loop issues can occur if the device is not receiving sufficient power.
5. Professional Repair: If none of the above steps work, it's possible that there is a hardware issue. In such cases, you may need to consider professional repair services or contact Bushnell for further guidance.

1. Boot the computer to the boot menu: To do this, restart the computer and press the appropriate key when prompted to enter the boot menu. On most eMachines computers, this is the "F12" key.
2. Select the CD/DVD drive as the boot device: Use the arrow keys to select the CD/DVD drive and press the "Enter" key to boot from it.
3. Insert the Windows ME boot disk: Insert the boot disk into the CD/DVD drive and restart the computer.
4. Choose the "Start Computer with CD-ROM support" option: When prompted, choose the "Start Computer with CD-ROM support" option.
5. Run the Windows ME setup program: The setup program should start automatically. Follow the on-screen instructions to install Windows ME.
6. Format the hard drive: During the setup process, you will be prompted to format the hard drive. Choose the "Full" format option to erase all existing data and perform a complete factory reset.
7. Install Windows ME: Continue to follow the on-screen instructions to complete the installation of Windows ME.

After the installation is complete, the computer should be in a factory reset state and you can begin setting it up as a new system.
Please note that resetting your computer to the factory settings will erase all personal data and installed programs, so be sure to back up any important data before proceeding with the reset.

If your Samsung Galaxy S02 is stuck in boot mode, there are a few steps you can try to troubleshoot the issue:

1. Restart the device: Try restarting the device by holding the power button for a few seconds and selecting "Restart." This may resolve the issue if the device was simply stuck in boot mode due to a temporary glitch.
2. Boot into Safe Mode: If restarting the device does not resolve the issue, try booting into Safe Mode. To do this, turn off the device and then press and hold the power button until the Samsung logo appears. Then, release the power button and immediately press and hold the volume down button until the device finishes restarting. If the device boots into Safe Mode successfully, it may indicate that a third-party app is causing the problem.
3. Wipe the cache partition: Another option is to try wiping the cache partition. To do this, turn off the device and then press and hold the power button, volume up button, and home button until the Android system recovery screen appears. Use the volume buttons to navigate to "Wipe cache partition" and then press the power button to select it. Wait for the process to complete and then reboot the device.
4. Factory reset the device: If none of the above steps resolve the issue, you may need to factory reset the device. This will erase all of your data, so be sure to back up any important files before proceeding. To factory reset the device, follow the steps above to boot into Android system recovery and then select "Factory reset" and follow the prompts to complete the process.

If you have tried these steps and the device is still stuck in boot mode, it may be necessary to seek professional help or contact Samsung customer support for further assistance.

ck this out hope it helps.

https://www.youtube.com/watch?v=j7G93cWDVqo

Hi.

If you recently had a modification on your ROM, you may be experiencing a BOOT LOOP which is common to Android Tablets. A factory reset would be the best solution to that. Here's how to do it;

Turn-off your Tablet by long-pressing your power button. To be sure it's totally shutdown, wait for at least 30 seconds before proceeding to factory reset. If your tablet's battery can be removed, it would help if you detach the battery and put it back again before proceeding.

Resetting your Tablet to factory setting erases all the data in your tablet's memory, so you have to be ready to encode all contacts again and stuff like that.

Factory Reset Proper;

1. Press VOLUME UP and POWER button at the same time without releasing until the device boots to "Recovery Mode".

2. In Recovery Mode, scroll down by pressing VOLUME DOWN until you reach the option "Swipe Data/Factory Reset" or any equivalent to Factory Reset therein.

3. Follow through the succeeding menus until the device initiates the reset.

Note: If your Device has a HOME button (usually located at the Center-bottom of the LCD), the buttons to be pressed to enter into Recovery Mode are HOME and POWER at the same time. Release only after the device shows it boots in Recovery Mode.

I hope this helps you.

Try holding volume Up and volume down together then the power button----hold all three until vibration starts.......that should get you to a factory reset.

https://www.support.xerox.com/support/workcentre-7132/documentation/enus.html

Resetting the MC75

There are two reset functions, warm boot and cold boot. A warm boot restarts the MC75 by closing all running

programs. A cold boot also restarts the MC75, and also resets the clock. Data saved in flash memory or a memory

card is not lost.

If the MC75 is not functioning properly, perform a warm boot first. If the MC75 still does not respond, perform a cold

boot.

Performing a Warm Boot

Hold down the Power button for approximately five seconds. As soon as the MC75 starts to boot release the

Power button.

Performing a Cold Boot
To perform a cold boot simultaneously press the Power button and the 1 and 9 keys.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

This might help, but I don't know how to put it in tech mode.

"The fuser error reset code will reset the machine so it will run after the problem is fixed.First remove any jam in the fuser then enter tech mode;
press program, * ,clear, * enter 1 4 press start then turn machine off and then back on."