My code does not work and I don't my key the code keeps changing by its self

I always ask---If you went to the trouble to have
it scanned & get a nice print out & I would assume
asked all these questions at the shop,then why
did you not leave it,to be further component tested
& issue resolved?

TAC -throttle actuator control

The drive by wire motor that opens the throttle
body plate

TPS Sensor--throttle position sensor on the same

Try spraying some CRC Throttle Body Cleaner in
there around the throttle plate

After that you need to have to tps sensor tested
I wouldn't be in a hurry to change a throttle body,
they cost hundreds & the codes don't tell you it's bad

The only time you replace a throttle body is if you can not
get the motor by it's self

if you or some one you know has an account with ebay go to ebay and look for the keyboard they don't cost to much.then go to youtube and type how to change the keyboard for your loptop model and watch videos and you will be able to change it is simple beleave me.i have doned my self.and im not an expert person.

Hi keep teaching should come up with more if still dosent work try one for all web site or phone them very helpful

best result : just download unlockme.sis application & install it on your nokia 6600 and open it after 10 to 15 minute lock code appear on display .


to remove virus you have to formatt your phone , frist switch of your phone & start the device by pressing combination key green key ,' * ' , ' 3 ' , ' power on/off switch ' you will show formatting on display , make sure that procees remove contacts messages etc. so please back up your data before formatting

try changing the needle
try rethreading the machine
clean under the needle plate & in the bobbin area for lint or threads
if these suggestions don't help, then the machine needs to be checked
to see what wrong with it

You wouldn't really expect the whole world to know
your code would you? Your on the internet,people
know you & want to steal your vehicle

You go to a dealer with your tittle,registration,drivers
licence

They don't just give that to anybody

They will give you the factory code

Why don't you have the card it came on with
the owners manual?

If you got no manual, have the dealer write down
how used the key less entry & how to change the code

EVAP Purge Control Valve Circuit

I don't have a break down on all the evap codes

There are others that say the same thing & I do not
want to tell you to change any part,no one should

You always use the codes to guide you to a system
area & then do some testing

You will need a repair shop
Don't throw parts at it

You can learn a lot on YOU TUBE about what an evap
system is & how they work

Also several parts manufactures web sites have educational
video
You can watch that stuff all day long for years & never see it all
No reason not to educate your self when you have an internet connection

The key has to open the drivers door

Raise the car up,support it,& put your battery
charger on the starter battery cable terminal
& ground the black clip

Try charging the battery for 4 hours or so

Call vendor and explain your situation and ask for the registration key code.

F90 Maximum oven door unlock time exceeded.
F91 Maximum oven door unlock attempts exceeded.
F92 Maximum oven door open time exceeded.
F93 Maximum oven door lock time exceeded.
F94 Maximum oven door lock attempts exceeded.


1. (F90, 91, 92, 93 & 94) Check the wiring between EOC & Lock Motor Micro Switch.

2. (F90, 91, 92, 93 & 94) Replace the Motor Door Latch assembly if necessary.

3. (F90, 91, 92, 93 & 94) Check for binding of the Latch Cam, Lock Motor Rod & Lock Motor Cam.

4. (F90, 91, 92, 93 & 94) Check to see if Lock Motor Coil is open. If open, replace Lock Motor Assembly.

5. (F90, 91, 92, 93 & 94) Lock Motor continuously runs - if Micro Switch is open, replace Lock Motor Assembly.

6. (F92, 93 & 94) Check oven door Light Switch - if open, replace Switch.

7. If all situations above do not solve problem, replace EOC.


F90 is a door lock code, Try this...
unplug the range.
wait 1 minute.
turn the range back on,
then while holding in on the oven door.
start another self clean.
wait 2 minutes.
then cancel the self clean.

do not release the door until the door lock light goes out.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question@#$%