Sharp LC32D44EBK 32 in. LCD TV Logo

Related Topics:

A
Anonymous Posted on Jan 02, 2013
Be the first to answer

Lc32d44ebk stuck in stand by mode

TV power lamp goes green for approx 15 sec then reverts to stand by. I can get it into service mode by holding down input an volume - buttons (then Vol - and CH - buttons) The screen goes black after a few seconds but stays on long enough to show :- 1) 1b lamp error 2) 1b lamp error 3) 1b lamp error 4) 1b lamp error 5) 1b lamp error

Answer This Question

4 Related Answers

Anonymous

  • 699 Answers
  • Posted on Feb 07, 2011

SOURCE: When I turn the TV on, the green power light comes

Your TV will need to go to service agent for repair.

Ad

Anonymous

  • 134 Answers
  • Posted on Feb 20, 2011

SOURCE: I have a Sharp LC-46E77UN

THe problem is in the set top box. Or common called the tuner box. IT looses the 5 volts to the main display and thus the monitor will go into a shut down state. THESE boxes are factory repair only and must be sent off to repair.

Anonymous

  • 2 Answers
  • Posted on Apr 08, 2011

SOURCE: Sharp LC37D44U Power LED was flashing green. TV

I had the same problem. all the service reset would only make the display come on for a few second with no "k" on the screen - only the channel would show up. I purchased a complete set of board for the lcd on ebay, and started swapping them one by one. The inverter boards were the culpret. Tele working 100% since that board swap.

AJIN G

Electro Med Services

  • 6694 Answers
  • Posted on Jan 07, 2017

SOURCE: Sharp lcd tv. Grn lite flashing, reset by unplug, vol + ch - , plug in. Tv came back on, after few mins screen goes blk, have sound. turn off and on picture back for few minutes, goes blk, snd ok.

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. The site has set-up code list & set-up procedure to many popular brand remote controls. The site has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Set-up code list to many brand remote controls also is given. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://electro-medical.blogspot.com/

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Picture and sound come and go on antenna or dvd
Try another lamp. Error 5 is Lamp power supply, but its usually always the lamp bad.
Read full answer
Mar 27, 2014 • Sony Grand WEGA KF60WE610 60" Rear...
0helpful
3answers

Samsung HL-R4266W 42 in won't turn on
Hi,

Initially, have you tried a full hard reset? If not, pls unplug from the mains. Most current devices would reset and revert back to factory default settings (assuming no internal hardware fault) when unplugged for a considerable period of time (from a few minutes to a couple of hours).

Additionally, have you tried powering the unit using another outlet?

Pls post back for any development(s) or even the lack of it.

Hope this be of initial help/idea. Good luck and kind regards.

Thank you for using FixYa.
Read full answer
May 01, 2008 • Samsung HL-R4266W 42" HDTV-Ready...
0helpful
1answer

HI, MY NAME IS S. A. ANSARI, I HAVE A SHARP AQUOS LC-32A66M LCD TV. ONE DAY SUDDENLY GOES INTO STAND BY MODE. NOW WHENEVER WE TRIED TO TURNED IT ON, IT ON FOR 30 SECOND I.E. WE CAN SEE PICTURE, HEAR SOUND...
Hi Ansari
It sounds like a main board problem. The control voltage that goes to back-light inverter board; from the main board, goes down. Contact any service technician. This is not a user repairable fault. Gopakumar Gopalan Google
Read full answer
Feb 27, 2014 • Sharp LC-32A66M 32 inch Multi-System Full...
0helpful
1answer

GREEN SCREEN
Try initialize the TV. If works, great. If not, doesn't hurt. Worth to give a try.

I had whole redish/pinkish screen on my 50v500 starting a few days ago, then I read through each of the threads on this site for the samilar problems on my model. I found TVtechmaniac's solution (pasted below) solved my problem. Thank you TVtechmaniac!

Enter the I2C Service Menu, be sure the power is OFF.
1. On the front control panel, press and hold the INPUT button.
2. Then press the POWER button for two seconds.
3. You may keep the INPUT button depressed until you see the OSD with the Service Menu displayed.
4. If you don't see the service menu, please repeat Process making sure you wait until the Power blinking LED stops.
5. Execute the Memory Initialize operation after the adjustment values have been written on a sheet of paper. Highlight "MEMORY INTI", arrow to the right and hold the button to the right (approx 5 sec.) until a check mark appears in the box. This activates the Memory Initialization.
6. After the Memory initialize operation has finished (10~15 sec, the channel will revert to CH 3.) the pink image symptom should be fixed.
7. Write back the adjustment values from your notes to their respective adjustment parameters in the adjustment mode. (In other words, set the Data Values back to the the Data values written down before the Memory Initialization procedure). NOTE: Make sure the SELECT Button is pressed on remote after every change to the values. Failure to do so will result in the data values not being changed.
8. Exit I2C menu. Press exit repeatedly until you go back to the normal picture.
9. Turn the set off-on and Confirm the picture remains in a good condition.
BE SURE TO COPY DOWN DATA SETTINGS BEFORE INITIALIZING I2C SETTINGS
Read full answer
Jul 12, 2012 • Hitachi 50V500 50 in. HD-Ready LCD...
2helpful
1answer

Sharp lc32d44ebk stuck on standby tv no picture green light comes on then goes straight to red
Hello,

Ur power supply board is dead, u know basic electronics’ and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get ur tv power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

Good luck and hope this helpout....




Read full answer
Aug 03, 2010 • Sharp LC32D44EBK 32 in. LCD TV
1helpful
1answer

1-Projector is in standby, so I hit the power button. 2-Green power light comes on, and lamp light flashes green (warm-up). 3-Lamp light goes solid green, but no picture. (However, if you look at the lens,...
I think it's capacitor issue on the power supply board. open it, look for power supply board and fine bloated capacitor and replace it.
Read full answer
Feb 15, 2010 • Sharp XR-10S DLP Projector
41helpful
2answers

Alarm light on and u051 error mx310
Hi

You’ll need to reset your printer to clear the ink counters, after resetting it’ll not display the error code again. Follow this procedure to reset the printer--

1. Power off the printer.
2. Holding the stop/reset button, press and hold power button also. Hold both buttons together for 5 secs.
3. Still holding the power button, release the stop/reset buton, then press the stop/reset button twice.
4. Release power button (the screen should now say 'Service Mode').
5. Wait until the power button lights steady green, then press the stop/reset button three times with a 3 sec space between each press. On the 3rd press the indicator should turn steady orange.
6. Press the power button once, (the orange light should go off).
7. Open the printer and remove both cartridges. Wait for 10 seconds. Replace the cartridges and close printer. Wait for 30 seconds.
8. Press the power button, and wait until printer has shut down.
9. Press power button to power up. The printer will feed one piece of paper, then ask you to set the language.
10. The page counter is now reset.

Please rate the solution & revert for further assistance.

Thanks
Rylee
Read full answer
Jul 29, 2009 • Canon PIXMA MX310 All-In-One Printer
0helpful
1answer

Stand by light flashes red on powering up with remote and the green light flashes approx 15 or times before the screen illuminates.
thats pretty normal, it takes a good second or two to warm up and the display to turn on(at least0, you get the green flashes as you hold for on, 1 sec is a long time at times, lol, be patient, no problem with your tv!
Read full answer
Apr 22, 2009 • Televison & Video
0helpful
1answer

Rastor needs adjustment on 60v500a
Enter the I2C Service Menu, be sure the power is OFF.
1. On the front control panel, press and hold the INPUT button.
2. Then press the POWER button for two seconds.
3. You may keep the INPUT button depressed until you see the OSD with the Service Menu displayed.
4. If you don't see the service menu, please repeat Process making sure you wait until the Power blinking LED stops.
5. Execute the Memory Initialize operation after the adjustment values have been written on a sheet of paper. Highlight “MEMORY INTI”, arrow to the right and hold the button to the right (approx 5 sec.) until a check mark appears in the box. This activates the Memory Initialization.
6. After the Memory initialize operation has finished (10~15 sec, the channel will revert to CH 3.) the pink image symptom should be fixed.
7. Write back the adjustment values from your notes to their respective adjustment parameters in the adjustment mode. (In other words, set the Data Values back to the the Data values written down before the Memory Initialization procedure). NOTE: Make sure the SELECT Button is pressed on remote after every change to the values. Failure to do so will result in the data values not being changed.
8. Exit I2C menu. Press exit repeatedly until you go back to the normal picture.
9. Turn the set off-on and Confirm the picture remains in a good condition.
BE SURE TO COPY DOWN DATA SETTINGS BEFORE INITIALIZING I2C SETTINGS
Read full answer
Jan 08, 2009 • Hitachi 60V500 60" Rear Projection...
2helpful
2answers

PT61LCX65 lamp timer
Hold the volume down button on the tv until the volume is at min. then continue to depress the volume down button on the TV. While depressing the volume down button the tv hold the pip or split button on your remote for approx 5 sec. You will see a box pop up that says lamp timer reset and gives instruction on how to exit.
Read full answer
Jun 02, 2008 • Panasonic PT-61LCX65 61" Rear Projection...
Not finding what you are looking for?

View Most Popular

LC32D44EBK 32 in. LCD TV

  • Televison & Video

Related Question

Picture and sound come and go on antenna or dvd

  • Sony Grand WEGA KF60WE610 60" Rear Projection Television

260 views

Ask a Question

Usually answered in minutes!

Popular Questions

37 inch Sharp Aquos. "Failed to receive Broadcast [E202]"

Sharp Aqous LC-26D5U Television

My 32" sharp lcd doesn't respond to the remote

Sharp LC-32SB24U 32 in. LCD TV

60" sharp aquos power indicator is flashing one short flash and one long flash and keeps repeating the sequence

Sharp LC60LE810UN 60 in. LCD TV

TV SCREEN GOES BLANK

Sharp LC-46D64U 46 in. LCD HDTV

Sharp Aquos LC-26D4U sound problem

Sharp LC-26D4U 26 in. LCD Television

Check Out the Latest HD Televisions Report
Check Out the Latest HD Televisions Report

View all Fixya Reports

Top Sharp Televison & Video Experts

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Cindy Wells

Level 3 Expert

6688 Answers

matt martin
matt martin

Level 3 Expert

1259 Answers

Are you a Sharp Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...