If ur ps3 console wont start up....then the things to check are>>> 1.check ur power cable 2.check whether u have inserted the disc properly and precisely. 3.check the insertion of memory card... 4.check the video port....... still the same problem,don worry check out the following Repair Guide..... CLICK HERE
The yellow light is also know as the yellow light of death casued by a hardware failure. It can be casued ny over heating a bluray drive failure, a hard drive failure or even a powersupply failure. You know you have it when you power up the yellow light flashes then you hear some beeps then the red llight flashes. I would suggest returning it if you have that option or getting it fixed somewhere else as a last option.
fix your PS3 so that it turns on again...
now the only reson there is 6 videos is because this one is a complete guild from tear down to rebuild... follow it exactly and you should be fine.
I want to just make it clear to you, that you can repair the following problems at home with a good repair guide. There is no technical knowledge needed you simply do what you see on the step by step vids or the paper guide.
The best thing is you get to keep your PS3 guide for life so if something goes wrong in the future you can just review your guide and fix it. so better download thisClick Here
Make sure the HDMI cable is connected to the HDMI OUT port on the
back of the PLAYSTATION 3 system. Connect the other end of the HDMI
cable into the HDMI Input port of the TV or display monitor.
While the PLAYSTATION 3 system is in standby mode (red light on the
front of the system), hold down the
touch-sensitive power button on the front of the system until the system
goes into standby mode again . (So the light cycle would go from:
red light --> green light --> then back to red light). This
will ensure that you have held down the power button long enough to
reset the Video Output Settings.
Turn on the PLAYSTATION 3 system and once the system finishes powering
up, the Video Output Settings will automatically reset to the standard
resolution (or detect the current display output settings of your
TV/monitor).
christian46
The WEP key is the security access key on your wireless router. If you do not know what it is you will have to log into the router and look it up. Below is links to access the WEP on a Belkin and SMC router. IF you do not have those or not those models let me know and I will make a walk through for you. Just let me know the make and model of your router.
Make sure the HDMI cable is connected to the HDMI OUT
port on the
back of the PLAYSTATION 3 system. Connect the
other end of the HDMI
cable into the HDMI Input port of the TV or display monitor.
While the PLAYSTATION 3 system is in standby mode (red
light on the
front of the system), hold down the
touch-sensitive power button on the front of the system until the system
goes into standby mode again . (So the light cycle would go from:
red light --> green light --> then back to red light). This
will ensure that you have held down the power button long enough to
reset the Video Output Settings.
Turn on the PLAYSTATION 3 system and once the system
finishes powering
up, the Video Output Settings will automatically reset to the standard
resolution (or detect the current display output settings of your
TV/monitor).
you can have a new connecter implaced to do so take it to a good electronics repair person it should only cost you aproxx $ 20 for the part plus there labour
i think......... i can help you
on this don't worry........ me too suffered with this problem ........... and i
solved my problem by getting code from this site .......... you too try this
...........ClickHere...........
Probably overheated and fried either a chip or a resistor on the mother board. If you still have the valid warranty I would suggest turning it in back to sony. If not you might want to open it up, diagnose the problem and replace and broken part(s).
1. Turn
off the PS3 so it only shows a red light. You can hold the power button
on the front until it goes into standby. To be sure, flick the power
switch on the back of the Play Station 3 off and then back on.
2.
Make sure your Play Station 3 is connected to your regular TV (not
HDTV) with the standard video cables.
3. Press and hold the power
button until the screen "flickers" and then immediately release. This
should reset the video settings.
4. Wait a few seconds, and the
Play Station 3 (PS3) logo should appear.
If this does not resolve
the problem, follow these steps:
1. Turn off the PS3 so it only
shows a red light. You can hold the power button on the front until it
goes into standby. To be sure, flick the power switch on the back of the
Play Station 3 off and then back on.
2. Make sure your Play
Station 3 is connected to your regular TV (not HDTV) with the standard
video cables.
3. Press and hold the power button on the front
until the Play Station 3 beeps and then turns off again. This should
reset the video for you and you can turn it back on after this.
it is the ylod caused by the lead free soldier they now use on the cpu. needs to be re-flowed, sent back to sony or sell for parts hope its helps you. also you tube ylod it will show you