20 Most Recent Lenovo IdeaPad Y510 Notebook - Page 4 Questions & Answers

It should be on your motherboard. You have to carefully disassemble you lap top .. Removing all Usb,Battery, and external connections.U need a small screw driver to take it apart.Leave your computer on for a day. If your need specifics let me know!

The thin plastic 'frame' in the front of the LCD screen, is the Display Bezel. Goes by many names. Display Bezel is used by HP.Display Mask, LCD Bezel, LCD Panel Bezel, and LCD Front Bezel, are a few other examples.Lenovo/IBM uses LCD Front Bezel.Lenovo doesn't show an HMM for the IdeaPad's, other than for the S9e series, and S10e series, (Notebook), plus the A1-07 series. (Tablet)(Hardware Maintenance Manual)http://support.lenovo.com/en_US/SupportSearchResults.page?searchText=ideapad+hmm(An HMM is a Service Manual)I also see there are no guides posted by users.Therefore we'll have to 'wing it', using my years of experience with repairing laptops, and you as the tech.1) Do you see any screw covers on the LCD Front Bezel?May not be the usual synthetic rubber covers. May be plastic, and the same plastic, and color as the LCD Front Bezel.Example,http://www.insidemylaptop.com/replace-broken-lcd-screen-lenovo-x60s-laptop/Scroll down to the photos in Steps 1 and 2.Also note the 'seals' on the side of the Display Assembly, shown in Step 2 photo.We'll start with this.2) Haven't worked on a Y510, and perusing the internet; it seems no one has found a solution, for removing the LCD Front Bezel off of an IdeaPad Y510.{ ALL power removed before beginning. Remove the AC adapter (Charger), and Battery }3) A) There is no sticky double-sided tape holding it on.B) Can't simply 'pop' it off, as with other Display Bezels, that do not use Philips head screws to hold it on.[ For all Display Bezels, (Other than this baby, perhaps), there are locking tabs on the outside edges of the Display Bezel. These match up to snap locks, on the inside edge of the Display Cover. (Top cover of laptop) When the Display Bezel is removed, the locks snap loose ]C) I suggest remove the screws which hold the Display Assembly to the laptop, and see if at the bottom of the Display Assembly, there are screw covers, or just screws, to remove.If there are, and no other screw covers/screws to remove, the LCD Front Bezel should pop off.This is what I mean by pop off,http://www.insidemylaptop.com/replace-screen-on-lenovo-g560-laptop/Step 2 and 3.{ The laptop is made by Wistron. (Philippines) One of the three major laptop manufacturers, that makes laptops for ALL laptop brand manufacturers.Such as Acer, Compaq, HP, Lenovo, Toshiba, Asus, you name it }Post back in a Comment.Regards,joecoolvette

Try this. You may need to add your operating system.http://consumersupport.lenovo.com/sg/en/driversdownloads/APR_Driver_List.aspx?CategoryID=307140&OS=0

OK, Here is the official Lenovo Service Manual for every component on the Y510.

http://consumerdl.lenovo.com.cn/UserFiles/UserGuide/en/User%27s%20guides%20and%20manuals/Y450/Lenovo%20IdeaPad%20Y450%20Hardware%20Maintenance%20Manual%20v2.0.pdf

However, removing the panel above the keyboard is not as simple as just removing the 4 screws located in the battery compartment and the three along the back edge on the bottom. Yes there are some "L" brackets on either end that are a pain to get to let go, but I found that by removing the DVD drive and removing the screw in the bay edge closest to the top panel, it helped loosen things to remove the top bezel. You may have to use a small flat blade screwdriver to pry the front edge up by the PF keys. Be careful removing the top bezel though, there are two small electrical ribbons attached to it for the volume and other controls. Once you have the top bezel ose, you simply have to lift the top edge of the keyboard and release the connector ribbon by flipping up the front edge of the connector. the manual illustrates this. Then it's just a matter of reversing the order. Reassembly is must easier and faster than disassembley.

Hello,

Locate your CMOS battery

Caution: When inside your computer make sure you're aware of ESD and all it's potential dangers.

Open the computer case and find the battery on the computermotherboard, verify that it will be accessible and that it can be removed. Most computers today use a coin cell CMOS battery as shown in the image to the right.

If you are unable to locate your CMOS battery refer to your motherboard or computer documentation or contact your computer manufacturer for additional assistance in locating it.

Obtain battery information

Unfortunately, most manufacturers will not list the exact type and model of your CMOS battery; therefore, once you have located the battery, write down all information about the battery (Voltage, chemistry, wiring, and packaging). If possible, remove the battery and take it to the location you plan on purchasing a new battery from. The part number for this battery for most computers is CR2032.

Additional buying information can be found on our battery buying tips page.

Removing the battery

Caution: When inside your computer make sure you're aware of ESD and all it's potential dangers.

If you're computer is using a coin cell battery similar to the above example picture. Removing the battery is relatively simple. use your fingers to grab on the edge of the battery and pull it up and out of the container holding it. Some motherboards have a clip holding the battery down. If your computer has this clip you may need to use one had to move the clip up and the other hand to pull the battery out.

Unfortunately, not all CMOS batteries are removable; some manufactures will only allow a replacement battery to be added. If you're not using a coin cell battery and are not able to determine how to remove it refer to your motherboard or computer documentation or contact your computer manufacturer for additional assistance in removing the battery or how to insert a new replacement battery.

Users with computers that do not have removable batteries only options to install a new battery will most likely also need to set a jumper when adding the new battery into their computer.

Insert the new battery

Once you have purchased a new battery, remove the old battery (as instructed above) and replace it with the new battery.

Enter CMOS values

Once the battery is replaced turn on the computer and resetting the CMOS values to the defaults. After the values have all been entered make sure to save the settings before exiting. Many CMOS setups allow you to press a key (such as F10) to save values and exit all in one action.

If after following all the above steps you continue to experience the same error when your computer starts or your computer is still unable to keep the stored values it's likely that you're experiencing a more serious issues. Most likely causes are bad power supply or bad motherboard.

just go to customersupport.lenovo.com and download drivers from there

for removing the BIOS passowrd we have to reseat the password jumpher which is there on the motherboard.try to search for the location of the pw jumpher on the motherboard online if you can or you can ask your service provider who will be able to locate the pw jumpher for you.

or better yet if your pc can sync gmail straight to your pc, check your email provider

Welcome to Fixya

The problem usually the computers charging system or the battery itself. You might need to erplace the battery first.

Please click link below for further assistance.

http://www.fixya.com/marketplace/servicepage.aspx?srvid=15511

Thanks If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

Welcome to Fixya

Try to enable /disable the camera by pressing Fn + Esc key.

Thank you for using Fixya! If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

When the CPU overheats then it will shut down (i.e. thermaloverload) and won't boot up again until it has cooled down. If this is theproblem is not fixed then the CPU will eventually fail.
A faulty fan causes the problem or the fan and heat sink assembly are cloggedwith dust.
Check the CPU fan to see if it spins freely, if not replace the fan.
If the fan and heat sink is clogged with dust the remove the dust and make surethe vents are clear and dust free. Use a can of compressed air to do this.

Welcome to Fixya

Make sure that webcam driver is installed in your computer. Test the webcam if it is working by using this site. Try to enable the webcam by pressing Fn + Esc key.

Thank you for using Fixya! If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

my friend hope it can help you this idea.
First you should press "Fn+F6" to turn on the camera, and then use the MSI software "Easy Face Manager" to display the camera locally or you can use one of the IM software like msn, skype ... to share camera with your friends.

Hi anshuman_sar,

Welcome to FixYa! How are you doing?

Try to reinstall the Lenovo Easy Camera Driver.

Please CLICK HERE to download the Lenovo Easy Camera Driver. There are 2 Lenovo Easy Camera Drivers there, one for Windows Vista and 1 for Windows XP. You just need to select the correct one.

Hope that helps. Please let me know if you have questions. Thank you for using FixYa!

Welcome to Fixya

Camera might be disabled. Try to enable it by pressing Fn + Esc key once.

Thank you for using Fixya! If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

Welcome to Fixya

You can disable/enable the camera by pressing Fn + Esc key once. This will turn on the camera.

Thank you for using Fixya! If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

Use another friends computer find and install the proper drivers for your mousepad and in the mean time you should be able to use a USB mouse.