20 Most Recent Canon MP140 PHOTO AIO All-In-One InkJet Printer - Page 8 Questions & Answers

Hello there
You may not see a paper jam.

This may work for you, it has worked for many here I given this advice so gave it a try it could work for you. Generally when this happens, something has fallen into the printer, or a piece of paper has been jammed in there.

First step, remove the ink cartridge, and turn the printer upside down and gently shake it, see if anything comes out.

If nothing goes, or you can't hear anything rattling around, get a piece of cardstock paper (60lb or heavier) and gently push this through the printer, to see if it will help push out what might be stuck in there.
And gave the rode that the ink slides on a good clean and maybe a bit oil on cloth and wipe the rod with it.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Hi there With most ( E ) errors

A) E5, E6 or E4 - it is cartridges error - to fix press the "stop\reset" button for 5-7 sec. and then release
it.

B) E27 - it is code for reset absorber (EEPROM reset or Waste
ink counter reset) and follow the described below
procedure:

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off

1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset

5) Turn off the printer.( it must be turn off)
then turn it on again.


Only in B) case you can enter into "service mode", in A) case or if have e.g. paper jam, or another error you CAN'T enter
the "service mode"
Try it

Anonymous see A) case: E5, E6 or E4 - it is cartridges error - to fix press the "stop\reset" button for 5-7 sec. and then release
it.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Hi, try removing the ink cartridges, cleaning their contacts and then replacing them. If this doesn't fix the problem, try replacing the carteidges with canon originals. This should do the trick!

E3 – Paper jam error.
How to correct, fix: Remove the jammed paper. If paper jams frequently occur, check the following:
1. Confirm there is no foreign material inside the machine.
2. Confirm only recommended paper is installed.
3. Confirm paper is installed properly.
4. Confirm the maximum number of sheets in the auto sheet feeder is within the paper limit mark.

E4 – Empty ink tank.
How to correct, fix: An ink cartridge is empty. To cancel printing, press the <Stop/Reset> button. To continue printing, press <Black> or <Color> button. After printing completes, replace the empty ink cartridge. Printing with an empty ink cartridge may cause the machine to malfunction.

E5 – The ink cartridge(s) is not installed. The ink cartridge(s) cannot be recognized.
How to correct, fix: Make sure to install both ink cartridges even when you set the machine to use only one ink cartridge in printing. If one of the ink cartridges is missing, this error can occur.

E7 – The ink cartridge is not installed in the appropriate position.
How to correct, fix: The ink cartridge is not installed in the proper position. Install each ink cartridge in the proper position.

E8 – The ink wasteabsorber is almost full.
How to correct, fix: The waste ink absorber is getting full. Press the <Black> or <Color> button to clear the error and continue printing. Printing can continue until the waste ink absorber becomes full. If the waste ink absorber becomes full, the machine will require service. The waste ink absorber is a part inside the machine, which absorbs ink used in the cleaning operations.

E9 – A specified period of time has elapsed without receiving a response from the digital camera. A print mode compliant with PictBridge is not selected. A specified period of time has elapsed without receiving a response from the digital camera.
How to correct, fix: The machine cannot communicate with the connected camera. Disconnect the cable between the machine and the camera to clear the error. Check the following items, then try printing again.
1. Confirm that the camera you are using supports PictBridge or Canon Bubble Jet Direct. If the camera does not support either one, the machine cannot print directly from the camera.
2. Set the camera in PictBridge print mode before it is connected to the machine. This is required before printing for some cameras that support PictBridge. Please refer to the camera instructions for more information about procedures required before and after connection to the machine.
3. There may have been no response from the camera for the prescribed time. Re-connect the cable between the camera and the machine.

E14 – Ink cartridge cannot be recognized.
How to correct, fix: Unsupported ink cartridge may be installed.

E15 – Install only recommended ink cartridges.
How to correct, fix: Install only recommended ink cartridges.

E16 – The ink level cannot be correctly recognized or detected.
How to correct, fix: A used ink cartridge may be installed, or the ink cartridge is empty. Press the <Black> or <Color> button, to clear the error and continue printing without replacing the ink cartridge. However, the remaining ink amount cannot be detected properly, so the function to detect the remaining ink amount does not operate.

E19 – Scanning failed error.
How to correct, fix: Scanning a document failed. Check if the document is placed in the correct orientation position and try the operation again.

Cut and Paste this url into your bowser>

http://www.usa.canon.com/consumer/controller;topic=609.msg73...?act=ModelInfoAct&tabact=DownloadDetailTabAct&fcategoryid=334&modelid=15294

The download the files.

Turn off the canon printer

Hold the Resume Button (red circle in the triangle), add a printer (click “Power”) an indicator light green.

Hold the Power Button, release the Resume Button.

Not releasing the Power Button, double click “Resume” and release Both Buttons.

Click “Resume” for Four times

Once you click “Power”, to confirm the selected action (reset counter absorber). To disable the printer “Power” button to click again.

Hi yes ok you can try

Turn off the canon printer

Hold the Resume Button (red circle in the triangle), add a printer (click “Power”) an indicator light green.

Hold the Power Button, release the Resume Button.

Not releasing the Power Button, double click “Resume” and release Both Buttons.

Click “Resume” for Four times

Once you click “Power”, to confirm the selected action (reset counter absorber). To disable the printer “Power” button to click again.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

I think this is the ink pads

Turn off the canon printer

Hold the Resume Button (red circle in the triangle), add a printer (click “Power”) an indicator light green.

Hold the Power Button, release the Resume Button.

Not releasing the Power Button, double click “Resume” and release Both Buttons.

Click “Resume” for Four times

Once you click “Power”, to confirm the selected action (reset counter absorber). To disable the printer “Power” button to click again.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Turn off the canon printer

Hold the Resume Button (red circle in the triangle), add a printer (click “Power”) an indicator light green.

Hold the Power Button, release the Resume Button.

Not releasing the Power Button, double click “Resume” and release Both Buttons.

Click “Resume” for Four times

Once you click “Power”, to confirm the selected action (reset counter absorber). To disable the printer “Power” button to click again.

You Need To buy Orignal Cartridge

Hi
You need to get some sort of paint program or art program software, I use the program called PaintShop Pro 7 it old program but I myself fine it Good, but make sure that the program you get has a scan on it, paintshop pro 7 got one but it needs to be added in from the options on to the tool bar, If was you I look for one on the internet to download.


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

solution see here http://wsoffice.blogspot.com/2010/01/canon-mp-injet-printer-reset-procedure.html

Its not an offical part of the homehub, but connect the MP140 and the HomeHub by USB, then on the computer you need to tell the PC that the printer is attached to the homehub rather than the PC. So on windows, start the add new printer wizard, and follow the steps on http://www.wallaceit.co.uk/Hardware/BT-Home-Hub---Use-it-as-a-print-server---Windows-XP-guide/80/article.aspx

go to this link...........
http://mallcom.wordpress.com/2007/10/23/canon-mp150-reset-codes/

http://www.jettecrefill.com/resetter.asp

Copy and paste this link for the help you need.

try to download the newest version from Canon's www site.

your printer driver is not properly install
you setup proper driver
send me your email
[email protected]

try to reinstall printer driver from manufacturer site and also reinstall ur pdf reader from adobe.

try to clean up your printer. to clean the printer open my computer r-click printer icon then go to preferences... the fulldown menu show options and go maintenance... and then lacate then clean option.

A small paper scrap could be anywhere inside, also one sensor sometimes gets bent when you pull out a jam, also there are small switches that go bad. Not enough to go on to be able to help without seeing the printer.