Top 20
Whirlpool RF364 Electric Kitchen Range Questions & Answers
Whirlpool oven question...FSEO on display
If you receive error codes F5-E0, F5-E1 or F5-E2, the door and latch switch need checking and possible replacement.
The door switch is #12 in the diagram (click image for zoom)...
Hope this helps.
Why my stove get the code f2E0? all ready unpluget
We are having the same problem. The technician is here right now, he is going to be replacing the keypad (control pad). We had to cut off the power because of the annoying beeping noise until he orders one. I hope this helps.
I'm trying to put the oven door back together and
I had mine apart to clean and could not figure out how it went back together. The side strips I thought helped hold the glass in but they dont. I then discovered the side plastic strips go back in on the flip side-inner oven side. Grrrrrrrrr...wasted half a day trying to figure this out.
What does pf display on stove mean
POWER FAILURE.
Your electric may have gone off.
The breaker may have been turned off and back on.
The range may have been unplugged and plugged back in.
You have loose wires in the range.
You have a defective control board.
One of the above will cause a PF code.
Good Morning - this is not a problem - only a
From page 9 of the user manual
This is a 12-hour clock and does not show a.m. or p.m.
To Set:
Before setting, make sure the oven and Timer are off.
1. Press CLOCK.
2. Press the TEMP/TIME "up" or "down" arrow pad to set the
time of day.
3. Press START/ENTER or CLOCK.
Hi, My GE Monogram ZDP30N4HSS range is making a
First I would replace both front igniters thier about $20 a piece this should fix the clicking. They keep clicking because they are not sensing the flame. The front burner assemblys will need to be thoroughly cleaned. There are very small orfice holes that need to be spotless. Also the burner cover, the top piece that pulls off. Make sure the bottom lip is very clean. Use a fine wire like a paperclip to clean out the holes in the burner assembly. For diagrams or illustrations enter your model # at
www.appliancehelponline.com
Pressed broil for the stove
Hello,
This error code
on a Kitchen Aid range indicates a keypad short on the Electronic Range
Control (ERC) board. This is the clock/timer on the operator console.
The recommended fix is to replace the ERC. You can generally find
replacement parts at these websites:
searspartsdirect.com appliancepartspros.com pcappliancerepair.com
All these sites offer great service with competitive pricing, so shop and compare.
Replacing an ERC is not a difficult repair and can be accomplished by
the average do-it-your self offer. If you decide to order the part and wish
to repair this on your own, follow these steps:
1. UNPLUG the range. Dangerous voltage is still present inside even with the range turned off.
2. Pull the range away from the wall and turn the unit around so you can access the rear panel.
3. Remove the screws on the back of the operator console.
4. Carefully disconnect the connector plugs to the ERC. Take note of
how they are connected, so that you can reinstall them correctly.
NOTE: The connectors are usually color coded with the colors printed on
the circuit board. However, if the colors are not printed on the board,
write them down. (A digital camera also comes in real handy for this).
5. With the connectors removed, remove the mounting screws to the ERC and the assembly will come out.
NOTE: Most replacement ERC boards do not come with the overlay. This is
the plastic pre-printed number display. The overlay can easily be
peeled off and re-used. Just make sure you properly orient the overlay
so that you don't inadvertently place it on the new board upside down.
If your existing overlay is damaged, you will need to order separately.
6. Install new ERC using the steps provided in reverse order. Minimize
handling the new circuit board with your bare hands to avoid damaging
the board.
I hope this instruction helps you.
Thank you for using fixya.
Read out says E4 F3 what does this mean?
Hi
Thanks for using FixYa. Error F3-E4 in your range means oven temperature sensor circuit failure. To resolve this issue you’ll have to check the oven temp. sensor circuit if the reading is more then 1100ohms then it should be replaced however, if the rating is fine then it is the Electronic Range Control (ERC) that has gone bad & should be replaced. Please do rate the solution if the issue is resolved or post a comment for further assistance.
Thanks
Rylee
I need the front glass
If you are referring to the outer glass for the oven door, it can be purchased at any of the following websites:
searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com
All these sites are reputable and have competitive pricing, so shop and compare. The first three sites on the list also have helpful exploded view parts illustrations to assist you with locating and properly identifying any parts you may need.
The exact part number will depend on your COMPLETE model number (located on a nameplate around the oven door or lower drawer opening). The part number will also depend upon the COLOR of your appliance. Make sure you pay particular attention to which part you order as the part number also identifies the color. The glass is listed as item 11 under the "Door Parts" listing.
If you have questions, please post back with your complete model number and let me know. I hope you find this information helpful.
Not finding what you are looking for?