Top 20
Pioneer PL-990 Turntable Questions & Answers
Pioneer htp-072 vsx-324--k-p
What receiver are you using and what input have you plugged this into? For more information, or should you have any further questions, please visit my website at audioserviceclinic.com. You may contact me directly through the website. Thank you.
Pioneer turntable to Pioneer VSX 515 receiver
I'm not sure what you mean by "Wot", but I assume you mean that the receiver doesn't have a phono input, as most receivers now a days don't. You will need a phono preamp. Cost is under $25.00. It provides the amplification to be able to use any high level(CD, DVD, AUX, etc) input as well as the RIAA equalization you need to decode the record correctly. For more information, please visit my website at audioserviceclinic.com. Thank you.
How to adjust the speed using the lights.
When the turntable spins the light shines on the edge. You will see at least two indications. One for 45 and one for 33. With the record playing you should adjust the speed control, till one of the indents appears static and not moving. You will have to do this for both speeds. You also might see some varations in speed. These are quite normal and getting it right is trial and error. It will only read true when the stylus is on the record too. If you can't get the indication to stay still then there is something wrong with the drive.
Need dust cover for pioneer pl-990 turntable
The only place to order one, is at Pioneer USA, as they have no distributors. It may or may not be available at this time. For more information, please visit my website at audioserviceclinic.com. Thank you.
I just bought a pioneer pl-420 direct drive record
If the player has a MD/MC pickup head, you need to use an input suitable for MD/MC
(Magneto Dynamic/Moving Coil). If that is not available, you need to buy a standalone
phono pre-amp (pre-amplifier with RIAA-correction curve). Like the TCC TC-400G/L.
Example: See
HERE and some info
HERE.
About 11 months ago I
Very odd! Sounds like it's not fitting in right. Are you sure that you have the right type of stylus for the cartridge? If in doubt replace the entire cartridge & Stylus. If it still plays up then it's in your amp after that course of action.
How install belt on pioneer turntable model PL. I
The simple rule of thumb is after you lift up the turntable platter turn it upside down and see if the belt sits on the inner rim tightly. That is if you after putting the belt on the rim and shake it upside down the belt should not fall off. And if you want to measure the belt-- remove it and place it in cold water for an hour and then after wiping it clean place it on its flat side on a table ( best is glass surface ). Measure its length with out stretching it in centimeters and subtract about a centimeter from the total. This will give you a new belts measurement
Eg; If the belt measures 19cm, subtract 1cm from it and go buy an 18cm.belt for replacement.
How can iget the belt
PUT IT ROUND THE PLATTER BASE FIRST,THEN LOOP A BIT OF STRING ROUND THE BELT LONG ENOUGH, SO WHEN YOU PUT THE PLATTER BACK ON,YOU CAN LIFT IT UP A LITTLE BIT WHERE THE MOTOR WHEEL IS THAT TURNS THE BELT, PULL THE STRING TOWARDS IT SO THE BELT GOES OVER IT.DROP THE PLATTER THEN PULL THE STRING OUT.
It needs a new belt
http://www.turntableneedles.com/Flat-Belt-Medium-236-Inch_p_255.html
Pioneer PL-990 is listed as a compatible player for this belt.
Pioneer turntable is powering up but not not
Turntable
Drive Belt
The chances are the rubber drive belt
has either broken or stretched so that it has fallen off the drive
pulleys.
You will need to gain access to the
underside of the turntable to replace it.
With most turntables the process will be
to secure the tone arm (a rubber band will do the trick) before turning the
whole thing upside down and unscrewing the base.
Replacement drive belts are easily
available on the internet. Search by make and model number of your turntable
Not finding what you are looking for?