Ricoh Aficio 2015 Copier - Answered Questions & Fixed issues

Main motor/ transport motor lock/ fusting motor error.

The only thing you can do is check for any obstructions in the machine.

That needs to be looked at by a service because the problem could be a motor, a pcb, or a power supply.

It can be a lot of troubleshooting to do.

press the orange key for say three times and press 107 and then press and hold the clear key for about three to four seconds . the machine zill take you to the sp mode. turn off the machine and put on again after a minute. good luck

Error SC 542 indicates a fuser temperature problem. Once the error is detected, the printer is toast until you manually clear the error from the keypad. Even though the printer is physically fine, it won?t come ready until the prior error condition is cleared. The magic keystrokes, clear the error code: The Fix In order to clear error SC542, you must perform procedure 5810. Press and hold online + escape, then power on. Use up and down arrow keys to select SP2 Press Enter Use up and down arror to locate SP5 Press Enter Use up and down arrow keys to select 810 Press Enter Confirm the selection Power off and on. The error code is now cleared.

1. Mode(Yellow Button) 2. 107 3. Press STOP Button for 3 second (RED Button) 4. Copy Sp 5. 5810# 6. Excute 7. Power Off 8. Power On

the best for u is replace pcu

TD sensor abnormal • Poor connection of the PCU

The mechanical total counter is disconnected.Possible Causes• User removed the counter while it was operating• Poor connection• Mechanical total counter defective

You should have a service technician come look at the machine. sc542 is a fuser code, which could mean that a thermostat was blown, or it could be a dirty or defective thermistor. A Ricoh technician will be able to inspect the fuser and make that determination, and hopefully get you up and running right away!

SC 350 relates to problem of ID or image density sensor, first of all clean it with IP and check if problem persists go to SP mode and check in input check under modes,replace sensor if found defective,if problem resolves but recurs again check for toner flying and developer and drum life, chances of sensor failure are very less.

machine needs drum and developer, but a temporary fix would be...open front door near notice green handle where toner is replaced, look to the right of green handle and down about 2 or 3 inches, you should see a plastic or chrome cover the size of a postage stamp, remove the cover and you should see a 3/4 inch wide piece of glass barely sticking out, carefully grasp the glass and pull it out of machine, wipe the toner off the glass , put glass back in and replace cover , shut front cover and run copies .

describe problem in more details about what technic u are using to scan , desktop binder or scan to email?

if u have service manual u can load new developer by ur sel but if u r not technician its hard to load develpoer. u can by to me a service manual. email me at [email protected]

DO U HEAR NOISY WHEN THE COPIER IS RUNNIN? IF YES...CHECK THE DEVELOPING UNIT MAYBE HAS PROBLEM IN LOWER DEVELOPING UNIT

Maybe you meant photoconductor there is no web in copier. Or you got wrong model of copier

Are you a tech? I suspect not. You need to remove the drum unit, disassemble, separate the drum from the development unit. Remove cover of developer unit, add developer, reassemble, and run SP2214 to calibrate.
This is NOT a procedure to be performed by an end user...no disrespect intended.

Exposure lamp error.Verify the exposure lamp and the expo lamp thermistor.

replace thermistor &enter sp program &turn m/c off and on

you can try to reset the code by entering into service mode, just enter into service mode and then shut down the machine by the main switch and then turn it on after 30 seconds. For to enter into service mode press the following keys in the next order: press the yellow key ; then press 1-0-7 and then press the red key and hold it pressed until on the screen do not show service mode. If after this again the machine gives fusing error, it means that you have problem some part in the fusing unit. possible is the termistors or the teromstats

Yes, If you have installed a main motor from Aficio 1015 the machine will work and there will be no SC Code displayed, but the machine will print a reduced image. The part number for the main motor for Aficio 2015 is : " AX06 0270 Brushless Motor 24V/20W "