20 Most Recent
Elna 2005 Mechanical Sewing Machine - Page 3 Questions & Answers
How to thread an Elna 2005
Hi. I've searched a number of my sources for a manual for your machine, but the closest I could find is for the 2002-2004-2006 models at http://www.mastersewusa.com/info_elna_2002_2004_2006.html
Threading should be similar enough between your machine and the ones covered in this manual that you can see what's going wrong.
Hope this helps!
Robbie
7/30/2010 8:57:20 PM •
Elna 2005...
•
Answered
on Jul 30, 2010
My machine has started to sew upside down (the
Check the needle to be sure it is properly installed.
This is usually with the flat side of the needle shaft facing the back of the machine - refer to the manual for this machine to be certain.
Always thread a sewing machine with the presser foot up as this opens the tension control for proper seating of the thread.
5/7/2010 4:28:21 PM •
Elna 2005...
•
Answered
on May 07, 2010
Cloth will not move forward
Cogs are feed dogs.
Check your manual to see if there is a pressure adjustment for the presser foot.
This may be a nob on top of the machine directly over the presser foot.
Turning the adjustment left/less or right/more pressure.
Also, refer to the manual for cleaning the bobbin and feed dog area as lint may be causing a bit of the problem.
5/1/2010 5:45:07 PM •
Elna 2005...
•
Answered
on May 01, 2010
My Elna Stitch Craft 4000 sews very small stitches even after I adjust the length?
It sounds like there might be an issue with the settings or mechanism of your Elna Stitch Craft 4000 sewing machine. Even after adjusting the stitch length, if it continues to sew very small stitches, there are a few things you can try:
1. **Check the Stitch Length Dial**: Ensure that you are adjusting the stitch length dial correctly. Sometimes, the dial may not be turning properly or may be stuck, leading to the machine sewing at the same small stitch length regardless of your adjustments.
2. **Clean and Oil the Machine**: A sewing machine that hasn't been cleaned or oiled in a while can have issues with stitch length consistency. Follow the manufacturer's instructions to clean out any lint or debris from the machine and oil the necessary parts.
3. **Inspect the Feed Dogs**: The feed dogs are responsible for moving the fabric through the machine. If they are not functioning properly or are obstructed, it can affect the stitch length. Check for any debris or damage to the feed dogs and clean or replace them if needed.
4. **Check the Bobbin Tension**: Incorrect bobbin tension can also cause irregular stitch lengths. Make sure the bobbin is correctly threaded and that the tension is adjusted according to the machine's specifications.
5. **Test with Different Fabric and Thread**: Sometimes, the type of fabric or thread being used can affect stitch length. Try sewing on different types of fabric with different threads to see if the issue persists across various materials.
If none of these steps resolve the problem, it may be necessary to have the machine inspected and serviced by a professional technician. They can identify any underlying mechanical issues that may be causing the small stitch length problem.
How do I fix the tension on my Elna Stella air electronic sp?
The following is an excellent video on how to check tension. She shows how to check bobbin tension and top thread tension (presser foot down). Then how to adjust top thread tension to get the stich to sit at mid fabric.
https://youtu.be/YF7EOCvpHLg
Thread nesting on the bottom side is almost always top tension too low or top thread is not in the tension discs (when foot down) but can also be top thread not feeding evenly, or a burr on either the bobbin case or hook race or debris in the hook race, or needle hook interference.
Always be sure to thread your machine with presser foot up. With foot up, the tension discs are separated to accept the thread.
Dont know what type of fabric your curtains are. You might try test sewing with a different tight weave cotton fabric just to see if it you can get it to work.
Zig zag not working on Elna Carina seeing machine
If the zig zag function on your Elna Carina sewing machine is not working, there could be a few possible causes:
- Incorrect stitch selector: Make sure you have selected the correct stitch on your machine. Double check that you have selected the zig zag stitch, and not accidentally switched to another stitch.
- Incorrect stitch width: The stitch width knob on your machine controls the width of the zig zag stitch. Make sure that the stitch width is not set to zero, as this would prevent the zig zag function from working. Adjust the stitch width to the desired size.
- Tension issues: If the thread tension is too tight or too loose, it can affect the zig zag stitch. Check your thread tension to make sure it is set correctly.
- Clogged machine: Dust, lint, and debris can accumulate inside your sewing machine and affect its performance. Clean your machine thoroughly, including the bobbin area and the feed dogs.
If none of these solutions work, it may be necessary to have your machine serviced by a professional.
Not finding what you are looking for?