Kodak Esp 1.2 All-In-One Printer - Answered Questions & Fixed issues

To help you troubleshoot the issue, please follow the steps as given below: - Make sure printer power connections are firmly connected to both end of power connector. - Make sure power switch is turned on. - Please try swapping the power point that is working properly. - Please change the power cord to see if that is the issue. - If issue persists, it is recommended to contact 'Kodak Support Center' from the link given below for further troubleshooting as it might be internal hardware issue: http://support.en.kodak.com/app/contact/selected/true GuruAid.com

clean rollers or order new ones for 50 cents, just google search for the rollers, also check to see what weight paper you are using, it may work with other or check paper size setting in printer setup. photo paper can be a problem re pick up with some printers

I'd uninstall the printer. Unplug the USB cable to the printer and power down the printer. Reconnect the cable, power up the printer and in control panel/printers "add printer" it should find the printer and install the latest driver.

On Printer Driver there is maintenance setting where you can perform head cleaning. just follow the instructions to do so..

bad power supply, chyeck it with a ohm meter if you can, Matt

check your print head it is stopeed up, remove it and clean with water just the jets, or use qtips, plain water no chemicals, Matt

www.kodak.com/go/support

be sure that the power supply is receiving the voltage

It could be a number of reasons: 1. a simple solution is to initiate what is called, 'power recycling' (although this is assuming that the printer did already work at some prior point); this is where you turn off the printer for about 5 minutes, then turn on, which usually allows the system to reengage itself. 2. did you install the software for the printer? If you did not then your PC might not know the printer is attached. Is the software installed properly?; meaning you must unplug the printer from the PC, then install the software, then connect the printer to the PC after the software is completely installed. If you did it in reverse, then you need to uninstall the software, then start over by doing what I just mentioned. 3. the USB port you have the printer cord inserted into could be bad on your PC. 4. the printer itself has an internal problem and needs to be repaired, or if the warranty is still in place, have it replaced with another new unit.

As soon as the alignment sensor does not work correct, or does get information it does not expect you get an error. The band whit the very small lines on it, should be clean and in one piece. It is connected to the print head and registers the slightest movement of the head. Check if the band is there and if it looks "new"

go to Kodak support web sit

This sounds like a communication error. If you go to "Printers & Faxes" or whatever your opperating system calls it (in Control Panel) is the printer greyed out and showing as 'Offline'?If so I have writtren a few guides for offline printer issues for Windows operating systems that can be found here: http://www.refreshcartridges.co.uk/igloo/how-to-make-your-offline-printer-online/Hope this helps.

Error Printer error 3806 3807 3808 3809 3810 or 3811 Kodak does not say what the error is but they do show how to deal with it.

hi Here is the link for a Kodak ESP 3 printer firmware download, Windows OS. http://support.en.kodak.com/app/answers/... Here is the link for a Kodak ESP 3.2 printer firmware download, Windows OS. http://support.en.kodak.com/app/answers/... Here is the link for a Kodak ESP 3.2s printer firmware download, Windows OS. http://support.en.kodak.com/app/answers/...

If the software and label haven't changed then there is a defect in the printer.

You may choose PCB assembly what you want on https://www.raypcb.com/

HOLA, ME PODRAS DECIR COMO HICISTE PARA DESMONTAR EL SCANNER DE LA IMPRESORA? MUCHAS GRACIAS

Dab the cartridges on a tissue and see if the image comes out solid, ink I mean. By doing this you can rule out the cartridge. Don't assume that fresh cartridges are okay. I have been in the printer business for years and seen many cartridges that are defective from the shelf.

Jill, try the attached link, if no answer there contact Kodak support. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info." http://resources.kodak.com/support/shtml/en/manuals/urg01238/urg01238c11s1.shtml Search How To Repair Any Kodak Printer

To help you assist with cleaning printer head for Kodak printer and copier, please follow the steps mention below: -Press 'Home' on the printer control panel. -Press the down arrow button until 'Maintenance' is selected, then press 'OK'. -Press the down arrow until 'Clean Print head' is selected, then press 'OK'. To help you further, you can refer the link given below: http://support.en.kodak.com/app/answers/detail/a_id/1459/~/cleaning-printhead-on-all-in-one-printer/selected/true GuruAid.com