Top 20 Price Pfister 42-YP0E Ashfield Single Control Lavatory Faucet With Pop-Up Questions & Answers

How are the other faucets in house working hot water wise .. often the 3/4 nipple plug's up just as it comes out of water heater . if other faucets OK the i have found the clog in the stop / valve feeding the hot side shut off water to house or shut off hot water at heater pull your stop & check it out ..if problem emanates from water heater replace or take screw driver & **** out nipple.. at w/h ..

Hi, David pressuming the water flow was good before you put in this new tap, then other than a problem with the tap! have you checked if you have an isolater valve on the pipe work under the unit, if so check that it is fully opened?
Thanks Paul.

It has to be adjusted at the water heater.

1 under the sink turn off both water supplies 2 disconnect the supply lines at the on/off valve EZer than at faucet 3 under sink unscrew the retaining nut(s) 4 on top wiggle or pry the faucet and lift up and remove. 5 know you can replace the spout and don't forget the new O ring that's why it leaks anyway. you really just need the new washer O ring . 6 Reinstall check for leaks 7 caulk around faucet. Hope this helps Mike

Back to the basics...did you turn the hot water shutoff back on? Is it a multi-turn shutoff or a 1/4-turn one? If it was old, and multi-turn, the washer could be shot, and it is all clogged. Try disconnecting the hose and see if you can get any flow into a bucket from the connection. There could be some crud caught inside of the cartridge, so you might need to remove it and flush it out. Price Pfister single handle sink faucet no hot water

910-024 (hot) and 910-025 (cold) https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0ahUKEwiEkf665I_ZAhWnTN8KHWZRAOEQFgg-MAA&url=https%3A%2F%2Fwww.pfisterfaucets.com%2Fsupport%2Ffaqs%2Fdetail%2F50160000000i5u7aac%2Ftwo-handle-4-lavatory-faucet-43-series-savannah-collection--install--troubleshoot&usg=AOvVaw3AdLnPNPr93k1HpVzuh8dr

Remove top and replace seals and springs

No be sure water is off. Take this apart with still being supplied will cause you a lot of trouble, wife will be very unhappy.

Here you go.

take the old one to the store with you they can match it up.. (home depot... lowes)...

dry rubber "O" ring/ threads on the shaft call a plumber to pull it apart , replace the seal and lubricate it

most aerators are screwed into the faucet IF you use a pair of multigrips with clothe folded in the jaws , you can apply gentle pressure and turn it out too much pressure and you will distort the aerator so be gentle with it

are you speaking of water hammer ? as typically this occurs when shutting off water , faucets that make noise like a whistle when on could be a part clogged aerator in the end of it , this happens over time and debris is aloud to collect in end of faucet

Go to manufacturer web site for manual download.

Download the instructions from the manufacturer.

drip 1-2 drip 1-2 drip no less then that or its liable to freeze how cold is it getting ?

Replace the cartridge or washer.

If I am not mistaken, the stems are specific to hot or cold. They turn in opposite directions. Someone may have put a hot stem instead of cold when doing a prior repair.

You may need to replace the cartridge(s) or rubber washers on the valve stems. Depends on what model faucet you have.

For a standard seat replacement you will need to shut off water and remove stem. Below the stem is the seat. It will either have a square center hole or hexagonal hole. If you don't have a seat wrench, you can get one at the hardware store when you pick up your replacement seats and washers. The new seats might not have the same inside type hole, so buying a tool that has both styles would be helpfull. Insert the correct seat tool into the seat and turn counter clockwise to remove seat. Reverse this to install new seat. Be sure to put a small amount of of pipe joint compound on the seat threads before installing. Replace the stem washers and reinstall on faucet. Make sure you take off the aerator or shower head and flush debris from system when you turn on the water. If your valve is a wall mount faucet with horizontal stems, you will need to take the faucet off at the union nuts and replace the seats from the back side of valve body. Remember, Lefty Loosy and Righty Tighty. Hope this helps and good luck.