SERP BELT DIAGRAM 1997 ECOCOLINE 150 V 6 NOT 5.4 AS POSTED ON CORE SUPPORT? HAS 8 PULLYS A/C P/S / ALT /CRK /WATER PUMP, 2 IDLERS 1 TENTIONER. FACING ENGINE COMPARTMENT A/C TOP RIGHT P/S BELOW LEFT SIDE (PASS) ALT TOP, IDLER THEN TENTONER THEN IDLER WITH 6 GROOV BOTTOM LEFT?

2002 with a/c, best I can do.




Item Part Number Description 1 10344 Generator pulley 2 8678 Belt idler pulley 3 8509 Water pump pulley 4 19D784 A/C clutch pulley 5 3A733 Power steering pump pulley 6 6B321 Crankshaft pulley 7 8678 Belt idler pulley 8 6B209 Drive belt tensioner 9 8620

there you go the timing is off:

http://www.obd-codes.com/p0016

alignment for timing:

http://www.2carpros.com/diagrams/toyota/avalon/2003

Not sure what engine you have so here is both.


Item Part Number Description 1 10346 Generator 2 6B209 Drive Belt Tensioner 3 3A674 Power Steering Pump 4 19703 A/C Compressor 5 6A312 Crankshaft Pulley 6 6C348 Idler Pulley 7 8501 Water Pump 8 8620 Drive Belt




Item Part Number Description 1 10346 Generator 2 3A674 Power Steering Pump 3 19703 A/C Compressor 4 6C348 Idler Pulley 5 6B321 Crankshaft Vibration Damper and Pulley 6 8501 Water Pump 7 6B209 Drive Belt Tensioner 8 8620 Drive Belt

Really don't need a diagram. Loosen the slide bolts on the power steering pump. loosen or tighten the pump by turning the jack screw (long transverse bolt) under the pump. Once the belt is tightened up, lock down the slide bolts and you are finished.

2 valve





Item Part Number Description 1 8679 Belt idler pulley 2 10344 Generator pulley 3 8620 Drive belt 4 3A733 Power steering pump pulley 5 6312 Crankshaft pulley 6 8509 Water pump pulley 7 2E884 A/C clutch pulley 8 6B209 Drive belt tensioner pulley
------------------------------------------------------------------------
4 valve


Item Part Number Description 1 19A216 Belt idler pulley 2 10300 Generator clutch pulley 3 8620 Drive belt 4 3A733 Power steering pump pulley 5 6316 Crankshaft pulley 6 8A528 Water pump pulley 7 19D692 A/C clutch pulley 8 6B209 Drive belt tensioner pulley 9 19A216 Belt idler pulley

1992 CHRYSLER LEBARON - V6 3.0L 2972cc 181ci GAS FI N 3

Serpentine Belt Diagram Alt., P.S., Idler & Tens.



More details you can find in DAYCO Catalog

I hope help you whit this (remember rated this help) Good weekend.

take off your serp-belt and spin your water pump, alternator, idler pully and see what squeaks or feels rough. your water pump bearings may be bad. the only thing you can do is change it. dont forget to change your thermostat and antifreeze. FYI your antifreeze is made with lubricants in it for your water pump bearings.

1. Remove the alternator & power steering pump drive belts.
2. Remove four (4) 10mm bolts holding the water pump pullys & remove the pullys.
3. Drain the Radiator (save coolant if intend to reuse).
4. Loosen & remove AC compressor belt.
5. Remove crankshaft pully (22mm bolt).
6. Remove lower timing belt cover (10 mm bolts) to access water pump bolts.
7. Remove the water pump (12mm bolts)
(1) Remove the 2 bolts, then remove the alternator brace (A). (2) Remove the water pump (B) and gasket.
8. Clean mating surface on engine & install new gasket & pump - reassemble. Refill w/50-50 coolant.

well has soon as you loosen and take out the alt the belt will become loose then put alt on it will slide down to put belt around and then pull up on alt and tighten it up

replace the serp belt and check idler and tentioner pullys. serp belts make noise after antifreeze or oil has been on them. good luck