How can I turn Off the VSC signal on my dashboard and what does VSC mean?

All explained here

https://forum.ih8mud.com/threads/a-trac-101.537946/

I have a 2000 land cruiser and my abs, active trac, vsc trac ...

https://www.justanswer.com > toyota > aqanp-2000-lan...

Oct. 10, 2017 - I have a 2000 land cruiser and my abs, active trac, vsc trac, vsc off, and brake light all came on at once. I have - Answered by a verified Toyota ...

2000 Toyota Land Cruiser Dashboard Lights & Symbols Guide

https://www.toyota.com > owners > resources > 2000

2000Land Cruiser ... Below are some commonly found Toyota dashboard lights ... Electric Power Steering (EPS) Warning Light [1] ... TRAC OFF Indicator [1].

Not sure if this will help, but my 2002 LEXUS sc430 had this issue, and it turns out that if you plug any scan tool other than the dealer unit in, it will cause this VSC lights to come on. It requires that you reset the "zero point calibration" for the skid system, which is done by first: have car on level ground with less than 1% slope in any direction. Next, follow these directions:

If you receive the "VSC" and "VSC Off" lights on the dashboard after a visit to a mechanic (often an independent mechanic using non-Lexus ODBII equipment), this means your "Zero Point Calibration" has been erroneously reset by a non-Lexus specific ODBII tool. This might especially happen if your state requires state inspection via ODBII, and you take your Lexus to a no-name place (like a Jiffy Lube or something). Follow the steps described in Post #6 in this thread to resolve this issue:
http://www.clublexus.com/forums/gs-2...d-vsc-off.html
Note that where you see a reference to a tool called the "SST 09843--18040", substitute that "tool" for a simple jumper cable (such as a short speaker wire) or a paperclip.
Here is the relevant excerpt from the above thread:
"The solution consists of approximately 15 step .
NOTE:While performing the Zero Point Calibration, do not tilt, move or shake the vehicle.
The vehicle must remain in a stationary condition throughout the entire process.
Be sure to perform the procedure on a level surface with an inclination of less than 1%.
Explanation of symbols:
SST (4-inch wire)
DLC3 (OBD-II connector under the dash)
TS (on the top row,pin number 3)
CG (on the bottom row,pin number 5)
(See picture below)
1. Ensure the shift lever is in the ''P'' range.
2. Turn the ignition switch Off.
3. Using SST 09843--18040, repeat a cycle of short and open between terminals Ts and
CG of DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for
TS and CG pin location in the DLC3).
4. Turn the ignition switch ON, do not start.
5. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
6. Turn the ignition switch OFF.
7. Be sure the terminals Ts and CG of DLC3 are disconnected.
8. Turn the ignition switch ON, do not start.
9. Check that the VSC warning light goes off about 15 seconds after the ignition switch
is turned ON.
10. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition
switch OFF.
11. Connect terminals Ts and CG of DLC3 using SST 09843--18040.
12. Turn the ignition switch ON, do not start.
13. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
14. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition
switch OFF.
15. Remove the SST from terminals Ts and CG of DLC3.
16. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete."
Attached images

you will need to hook up a scan tool, I know many parts stores will loan you one or let you use it in the parking lot, VSC could have something to do with a wheel mounted speed sensor, did you hit something? any noises, try this and see if it goes away

1. • 1 Shut off the vehicle's engine and apply the parking brake to protect yourself while working on the vehicle.
     
   • 2 Open the vehicle's hood and examine the engine compartment. Locate the air filter box mounted to the left of the engine. The air filter box features a black exterior, square in shape, and a large ribbed intake hose.
     
   • 3 Check all of the small black vacuum lines surrounding the air filter box. Reconnect any disconnected or loose vacuum lines you find.
     
   • 4 Start the engine and drive the vehicle to clear the "VSC" warning light displayed on the dashboard. If the VSC light fails to go out after driving the vehicle normally, proceed to the next step.
     
   • 5 Park the vehicle, turn off the engine and set the parking brake. Open the vehicle's hood and disconnect the battery's negative cable for 15 seconds, using an appropriate size socket. Disconnecting the negative battery cable will reset the vehicle's computer and clear the "VSC" warning.
     

The VSC is the Vehicle Stability Control. It appears there is a fault in the system somewhere. Also, if your Check Engine light is on, the VSC light will usually kick on as well. Fix whatever is causing your Check Engine light to come on first, and see if that also solves the VSC issus. I hope this helps! :) -Jason

check for size of 4 tires are same ,

Were you able to solve this problem

If you are talking about the "VSC Off" light, it means that the button to disengage your cars Vehicle Stability/Skid Control" system is engaged. Press the VSC button, the system should reengage, and the light should turn off.
If you are talking about the other VSC light, it means that your car has been forced to take evasive action to avoid a dangerous situation. For example, if you are driving on an icy road, and take a turn too tight, the vehicle may be forced to apply pressure to one of the brakes to prevent the car from loosing control. In this situation the VSC indicator light will light up to alert you that the action was taken, and remind you to possibly slow down.

VSC means Vehicle Stability Control.

It comes on when the sensor send a signal that the vehicle is not stable on the ground.....check the wheel balancing and alignment and the air pressure of your tires too.

Good luck.

Rate this solution.

As long as the "VSC OFF" is not illuminated, the VSC is ON.

The check engine light ,trac control light and VSC light are on. Does this normally represent a serious problem on a 2004 toyota solara?