My door lock wont unlock with the key i can turn the key in the door and the lock will go up if i hold it but wont stay up on its own so i cant get the door open. i pulled apart some of my door and still cant get it to open any suggestions

1. Get in your vehicle.
2. Close the door.
3. Put key in ignition
4. Do not turn on the ignition yet.
5. Hold down on the unlock button on the door panel. Do not let up.
6. Turn the key to ON, OFF, ON, OFF (while still holding the unlock button on the door panel).
7. Release the unlock button.
8. The door locks should cycle, indicating that you did everything correctly.
9. Have all your remote entry fobs available. Hold down on both the lock and unlock buttons until the door locks cycle. Do the same on all key fobs. This will re-program all of them.
10. Turn ON the ignition key to exit the program mode.
11. DONE.

if you talking about door latch wont let door close.try to reset all door locks.first if you cant get door close.work unlock button with remote or door switch.then hold open door handle while you flat screw driver pull up latch in door latch should stay up so door will close.once get door close.try resetting all door locks by sitting inside vechicle with all doors close.remove key from ignition.open drivers door.wait 24 seconds.turn ignition switch on and back to lock position 3 times.press and release drivers door courtesy light 3 times.ensure doors lock and unlock.if not wait 40 seconds and repeat procedure.if this procedure fails. you have problem in the door latch and lock mechanism inside the door itself.

REPLACE YOUR DRIVER SIDE DOOR LOCK MOTOR BEFORE YOU REPLACE IT DISCONECT IT FROM ELECTRICAL CONECTOR TRY LOCKING CAR IF IT WORKS THEN REPLACE THE LOCKING MOTOR LET ME KNOW MABY I CAN HELP IF YOU NEED ME TWO OK

hold the cetral locking lock all button down until the doors lock and unlock. The imobilser light goes solid red. At this point you have 10 to press the botton on your key 2 times . the doors will unlock and lock.

Use this procedure for New Body Style.
1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.
4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.
10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.
11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Sounds like the rod that goes from the lock to the key came off. There is usually a little plastic clip that holds it together and they break and you get what you are experiencing. You have to take the inside panel off of the door to get inside it.

probably gonna have to take the door panel off. You say it wont unlock or lock with the key? if thats the case its probably broke inside the door.

conect back the battery close all doors and windows driver door insert the key unlock the door one time and hold the key until window goes all way down then turn key to lock the door hold to lock position until windows go up if no stop repeat one more time right way without taking the key out , hope this help.

Here's what I suspect is happening. The door locks will lock and unlock normally when the key is OUT of the ignition. If the key is IN the ignition, the doors cannot be locked (manually, key fob, or otherwise, if the system is operating as designed - prevents the doors being locked when the key is in the ignition). I've seen this problem before, but on a Santa Fe, not an Accent. The ground signal of the right hand front passenger door was lost, and the doors automatically locked. Perhaps something similar is happening in the circuit between the ETACS module and the right front passenger door lock/unlock actuator. Could be anywhere in the circuit.




These wiring diagrams may be helpful. The relays expecially may help solve this issue. As you can see, these relays are also controled by the ETACS module (Remote Keyless Entry).