Where is O2 sensor circut bank1 sensor 2. And bank 2 sensor 2

that is the oxygen sensor up stream by the cataylic converter. you can get them at advance auto. you do not need to do the entire wire harness. good luck.

Change the O2 sensor.

Im curious if you had code erased after replacing the sensor? Simply by replacing the sensor will not reset the computer. You must have someone (Autozone) to check it and reset the computer. This takes a matter of seconds to a minute to hook a handheld comp. called an OBD2 into the vehicle under the dash. It will read the code and display the code, Then have them erase the code to see if it reappears.

The Powertrain control module (PCM) will provide a .45 volt reference voltage to the Oxygen sensor. When the O2 sensor reaches operating temperature, it will generate a voltage that will vary depending on the oxygen content of the exhaust. Lean exhaust generates a low voltage (less than .45V) and rich exhaust generates a high voltage (greater than .45V). O2 sensors on a specific bank marked as "sensor 2" (as this one is) are used to monitor emissions. A Three-Way Catalyst (TWC) system (catalytic converter) is used to control tailpipe emissions. The PCM uses the signal received from Oxygen sensor 2 (#2 indicates aft of catalytic converter, #1 indicates pre-converter) to read efficiency of TWC. Normally this sensor will switch between high and low voltage at a noticeably slower rate than the front sensor. This is normal. If the signal received from rear (#2) O2 sensor indicates that the voltage has "stuck" between .425V to .474 V, the PCM determines this sensor is inactive and this code will set.
Potential Symptoms Your check engine light(CEL), or malfuction indicator lamp (MIL) will be illuminated. There will not likely be any noticeable drivability problems other than the MIL. The reason is this: The rear or post catalytic converter Oxygen sensor does not affect fuel deliver(this is an exception on Chryslers). It only MONITORS the efficiency of the catalytic converter. For this reason, you will likely not notice any engine trouble.
Causes The causes for a P0140 code are fairly few. They could be any of the following:

• Shorted heater circuit in O2 sensor. (Usually requires replacement of heater circuit fuse in fuse block also)
• Shorted signal circuit in O2 sensor
• Melting of harness connector or wiring due to contact with exhaust system
• Water intrusion in harness connector or PCM connector
• Bad PCM

Possible Solutions This is a fairly specific problem and shouldn't be too difficult to diagnose.
First, start engine and warm up. Using a scan tool, watch the Bank 1, sensor 2, o2 sensor voltage. Normally the voltage should switch slowly above and below .45 volts. If it does, the problem is likely intermittent. You'll have to wait for the problem to surface before you can accurately diagnose.
However, if it doesn't switch, or is stuck then perform the following: 2. Shut off vehicle. Visually check the Bank1,2 harness connector for melting or chafing of the harness or the connector. Repair or replace as needed 3. Turn ignition on, but engine off. Disconnect the O2 sensor connector and check for 12Volts at the Heater Circuit supply and for proper ground on the heater circuit ground circuit. a. If 12V heater supply is missing, check the proper fuses for an open in the circuit. If heater circuit fuse is blown, then suspect a bad heater in the o2 sensor causing a blown heater circuit fuse. Replace sensor and fuse and recheck. b. If ground is missing, trace the circuit and clean or repair ground circuit. 4. Next, with connector still unplugged, check for 5 Volts on the reference circuit. If this is missing, check for 5 Volts at the PCM connector. If 5 Volts is present at the PCM connector but not at the o2 sensor harness connector, then there is an open or short in the reference wire supply between the PCM and the o2 sensor connector. However, if there is no 5 Volts present at the PCM connector, the PCM is likely at fault due to internal short. Replace PCM. ** (NOTE: on Chrysler models, a common problem is the 5Volt reference circuit can be shorted out by any sensor on the car that uses a 5 Volt reference. Simply unplug each sensor one at a time until the 5 Volts reappears. The last sensor you unplugged is the shorted sensor. Replacing it should fix the 5 Volt reference short.) 5. If all the voltages and grounds are present, then replace the Bank 1,2 O2 sensor and re-test.

You have a burned Oxygen sencer, and the transmission pressure sencer is bad also. Your heater has a bad switchover circuit. Hope this helps.

160....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)

P0161....O2 Sensor Heater Circuit (Bank 2 Sensor 2)

P0162....O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)

P0163....O2 Sensor Circuit Low Voltage (Bank 2 Sensor 3)

P0164....O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)

P0165....O2 Sensor Circuit Slow Response (Bank 2 Sensor 3)

P0166....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)

P0167....O2 Sensor Heater Circuit (Bank 2 Sensor 3)

P0168....Fuel Temperature Too High

P0169....Incorrect Fuel Composition

P0170....Fuel Trim (Bank 1)

P0171....System too Lean (Bank 1)

P0172....System too Rich (Bank 1)

P0173....Fuel Trim Malfunction (Bank 2)

P0174....System too Lean (Bank 2)

P0175....System too Rich (Bank 2)

P0176....Fuel Composition Sensor Circuit

P0177....Fuel Composition Sensor Circuit Range/Performance

P0178....Fuel Composition Sensor Circuit Low Input

P0179....Fuel Composition Sensor Circuit High Input

P0180....Fuel Temperature Sensor A Circuit

P0181....Fuel Temperature Sensor A Circuit Range/Performance

P0182....Fuel Temperature Sensor A Circuit Low Input

P0183....Fuel Temperature Sensor A Circuit High Input

P0184....Fuel Temperature Sensor A Circuit Intermittent

P0185....Fuel Temperature Sensor B Circuit

P0186....Fuel Temperature Sensor B Circuit Range/Performance

P0187....Fuel Temperature Sensor B Circuit Low Input

P0188....Fuel Temperature Sensor B Circuit High Input

P0189....Fuel Temperature Sensor B Circuit Intermittent

P0190....Fuel Rail Pressure Sensor Circuit

P0191....Fuel Rail Pressure Sensor Circuit Range/Performance

P0192....Fuel Rail Pressure Sensor Circuit Low In put

P0193....Fuel Rail Pressure Sensor Circuit High Input

P0194....Fuel Rail Pressure Sensor Circuit Intermittent

P0195....Engine Oil Temperature Sensor

P0196....Engine Oil Temperature Sensor Range/Performance

P0141....O2 Sensor Heater Circuit (Bank 1 Sensor 2)

P0142....O2 Sensor Circuit Malfunction (Bank 1 Sensor 3)

P0143....O2 Sensor Circuit Low Voltage (Bank 1 Sensor 3)

P0144....O2 Sensor Circuit High Voltage (Bank 1 Sensor 3)

P0145....O2 Sensor Circuit Slow Response (Bank 1 Sensor 3)

P0146....O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 3)

P0147....O2 Sensor Heater Circuit (Bank 1 Sensor 3)

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

Possible O2 sensors:

P2270 O2 Sensor Signal Stuck Lean Bank 1 Sensor 2
P2271 O2 Sensor Signal Stuck Rich Bank 1 Sensor 2
P2272 O2 Sensor Signal Stuck Lean Bank 2 Sensor 2
P2273 O2 Sensor Signal Stuck Rich Bank 2 Sensor 2
P2274 O2 Sensor Signal Stuck Lean Bank 1 Sensor 3
P2275 O2 Sensor Signal Stuck Rich Bank 1 Sensor 3
P2276 O2 Sensor Signal Stuck Lean Bank 2 Sensor 3
P2277 O2 Sensor Signal Stuck Rich Bank 2 Sensor 3
P2278 O2 Sensor Signals Swapped Bank 1 Sensor 3 / Bank 2 Sensor 3
---
This is Bank 1 (closer to the dash panel) Sensor 2 (located after the catalytic converter).

---
Note: A malfunctioning front oxygen sensor may cause fuel trim codes to set.

1. Several Diagnostic Trouble Codes use specific terminology to refer to sensor location. The illustration and key below explain the following terms:
2. Engine BANK Bank 1 is closer to the dash panel, (also referred to as RH or right hand). Bank 2 is closer to the radiator, (also referred to as LH or left hand).
3. UP Refers to Sensor 1 or "front sensor". It is located closer to the exhaust manifold and before the catalytic converter.
4. DOWN Refers to Sensor 2 or "rear sensor." It is located after the catalytic converter.
5. The following examples show how to interpret oxygen sensor terminology:
6. B1/S1 = Bank 1/Sensor 1 = Dash panel side, BEFORE the catalyst or "upstream"
7. B2/S2 = Bank 2/Sensor 2 = Radiator side, AFTER the catalyst or "downstream"

code is not for heater circuit,
code p0141=O2 Sensor Heater Circuit Bank 1 Sensor 2
that means its an oxygen sensor located in bank 1 which is the drivers side,sensor 2 means its the downstream sensor after the convertor

P0161 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
check the wiring to the bank 2 sensor, that is the one behind the catalytic converter on the opposite side from the bank where #1 cylinder is located, see firing order diagram below.