Where do you relieve the fuel pressure at when changing the fuel filter on a 1996 Plymouth Voyager with a 3.3L engine (short wheel base)

disconnect power supply to fuel pump, then start engine when engine stalls fuel pressure released

1. • 1 Make sure the engine is completely cool. Relieve the pressure in the fuel system. Disconnect the negative battery cable. Elevate the vehicle and support the fuel tank with a jack.
     
   • 2 Disconnect the fuel line from the front of the tank. Remove the ground strap, the inboard side fuel tank straps and the front T-strap fastener, then lower the tank approximately six inches.
     
   • 3 Take the fuel lines from the fuel pump module. Plug the fuel lines with golf tees to prevent the spillage of gasoline. Remove the fuel filter.
     
   • 4 Install the new fuel filter. Set the bolts in place and torque them to 40 inch/pounds. Tighten the main tank straps to 40 foot/pounds and the T-strap to 250 inch lbs.
     
   • 5 Reconnect the fuel lines in the reverse order of their removal. Lower the vehicle. Connect the negative battery cable.
     
   • 6 Start the engine and let it run for several minutes. Inspect the fuel lines for any leaks.
     

Read more: How to Replace a Fuel Filter in a Plymouth Voyager ' eHow.com http://www.ehow.com/how_4519932_replace-fuel-filter-plymouth-voyager.html#ixzz1WBXAZ7d3

Yes it does, It is located on the side of the fuel tank. You will need to lower the tank to disconnect the fuel lines. If you attempt to change this yourself be sure to disconnect the battery first. Also you will want to relieve the fuel pressure before removing the filter so that you don't get covered in fuel. I highly recommend that you go to a local parts store and purchasing a repair manual this will save you alot of problems the book cost around $25 dollars. Or find a local mechanic to do this for you most will charge around $25 labor only if there honest. Good luck

The line is under pressure so be careful when removing the fliter. You should be able to find the fuel pressure test port on the fuel rail under the hood. If you press in the schrader valve it will relieve the fuel pressure in the line and make it less likely to end up in your face when you finally remove the filter.

The filter is located under the vehicle on the passenger side about in the middle.

There will be two short sections of hose on each side of the old filter. Replace those sections of hose. Higher end filters usually come with the hose pieces. Use new fuel hose clamps. They are different than the regular hose clamps and do a much better job of keeping the hoses secure.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Where do you relieve the fuel system pressure at?

The fuel filter is either on the left side of the firewall or next to the fuel pump near the left side of the fuel tank.

1. Before servicing the vehicle, refer to the Precautions section.
2. Relieve the fuel system pressure.
3. Remove or disconnect the following:
   
   Negative battery cable Fuel filler cap Fuel lines from the fuel filter Fuel filter from the bracket

For 1996 Plymouth Truck Grand Voyager 2WD 3.0L MFI 6cyl the Fuel Filter is located under vehicle, driver side, below seating area, front of fuel tank, mounted on chassis in fuel line.

Hope help with this (remember rated this).

open gas cap to relieve pressure take a rag and small container and tools [open end wrenches] and under van by fuel tank follow fuel line and will see fuel filter disconnect old unbolt holding clip and install the rag is to clean debris from around filter and container is to catch to gas drips

Just getting ready to do this fix as well. The filter is located under the car beneath the drivers seating area. You have to release pressure in the system by taking the gas cap off and releasing the pressure at the valve on the fuel injection rail. After that it's just three slip connectors and a screw / bolt to remove and replace.

po352 is ignition coil B primary/secondary circuit malfunction---ignition coil #2----p0300 is random /multible cylinder missfire, muti cylinder missfire detected!!