I can't remove my rear rotors on my 2001 gmc jimmy. I already removed the caliper, brake pads and caliper bracket. Are there more bolts i need to remove or do i simply need to beat the rotor off?

Depending on vehicle. Find level ground and park there. Put chocks in front and behind wheels not being lifted. Loosen lugs, jack up vehicle, set jack stands, lower vehicle on jack stands, remove lugs and wheel. Open hood remove brake fluid cap. Remove two bolts holding caliper, pull caliper off rotor disc and bracket, remove pads, place a used pad in front of caliper piston, use a c clamp to push caliper piston in caliper, remove c clamp and old pad, hang caliper up, remove 2 bolts holding caliper bracket, remove bracket, remove rotor, install new rotor, install caliper bracket, install new pads, install caliper, repeat this on other side, put cap back on brake fluid tank, remove bleeder fittings and keep pressing brake pedal until an even flow of brake fluid sprays out. Install bleeder fitting. Make sure brake fluid doesnt get on paint and is contained and disposed of correctly, top off fluid install wheels and raise car up remove jack stands, lower car and break in new pads

Brake Pads Removal & Installation Front

To Remove:

1. Drain brake fluid to ½ full level in reservoir.
2. Remove the front wheels.
   
   
3. Remove the front brake caliper assembly.
4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
5. Remove the wear indicator from each of the 2 brake pads.

To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.

1. Using a large C clamp or equivalent press piston into the caliper.
2. Apply disc brake grease to the inside of each anti-squeal shim.
3. Install the anti-squeal shims on each pad.
4. Install the pad wear indicator clip to the pads.
5. Install the pads with the pad wear indicator plate facing upward.
6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
7. Install the front wheels.
8. Fill the master cylinder with new clean brake fluid.
9. Pump the brake pedal several times to seat the brake pads.

Rear TMC made rear brake components

TMMK made rear brake components

To Remove:

1. Drain the brake fluid to ½ full level in reservoir.
2. Remove the rear wheels.
3. Remove the caliper slide pins.
4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
5. Remove the rear brake calipers.
6. Remove the 2 brake pads with the anti-squeal shims.
7. Remove the anti-squeal shims and pad wear indicators from brake pads.

To Install:

1. Using a large C clamp or equivalent press the piston into the caliper.
2. Coat both sides of the outer anti-squeal shim with pad grease.
3. Install anti-squeal shims to each pad.
4. Install wear indicators on the 2 brake pads.
5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
7. Fill the master cylinder with new clean brake fluid.
8. Pump the brake pedal several times to seat the brake pads.
9. Install the rear wheels.

Brake Rotor Removal & Installation Front To Remove:

1. Remove the front wheels.
2. Remove the front brake caliper assembly.
3. Remove the front brake pads.
4. Remove the 2 bolts and caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the front wheel disc.

To Install:

1. Align the match marks and install the front disc.
2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the front wheel.

Rear To Remove:

1. Remove the rear wheels.
2. Remove the brake caliper assembly.
3. Remove the brake pads.
4. Remove the 2 bolts and the caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the rear disc.

To Install:

1. Align the match marks and install the rear disc.
2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
   • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
   • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the rear wheel

if the front are rotors there are two bolts that need to be taken off first.
remove the caliper, then remove the two caliper bracket bolts and remove the rotor
replace the rotor and reinstall the caliper bracket.
pull the caliper sliders and lube them with brake grease.
reinstall caliper sliders and install new pads and caliper
refasten caliper to bracket and your done

if your doing rear disc brakes same as front
if brakes are drum type you will need rear drum brake tools to release the springs and to refasten
the new brake shoes

1. here is some instuctions on how to do the brake pad replacement this should help you out
   
2. Jack up the vehicle on a secure metal part of the vehicle and place jack stands in the same area.
   
3. 2 Lower the jack until the weight of the car is solely on the jack stands.
   
4. 3 Loosen the lug nuts and remove the wheel from the vehicle, exposing the brake system.
   
5. 4 Loosen the caliper slide pins from the rear of the caliper and slide the caliper pins out of the caliper.
   
6. 5 Remove the caliper from the brake system and remove the old brake pads.
   
7. 6 Secure the caliper to a part of the suspension with a bungee cord to avoid it hanging by the rubber brake hos, where it could be damaged or start leaking.
   
8. 7 Loosen the two bolts that hold the caliper bracket to the vehicle and remove the caliper bracket.
   
9. 8 Pull the rotor from the vehicle.
   
10. 9 Measure the thickness of the rotor with the micrometer. Compare the measurement to the "minimum thickness" stamp on the rotor or the manufacturer specifications in the repair manual.
    
11. 10 Take the rotors to a machine shop to have them resurfaced if they are above specification and need resurfacing. Verify the manufacturer's recommendations in the repair manual, as rotors do not always need to be resurfaced or replaced.
    
12. 11 Reinstall the rotor on the vehicle.
    
13. 12 Place the caliper bracket back on the vehicle and hand tighten the bolts on the back of it.
    
14. 13 Torque the bracket bolts down to the manufacturer specifications in the repair manual.
    
15. 14 Place a new hardware kit in the caliper bracket and set the pads in the hardware.
    
16. 15 Press in the caliper piston with the caliper piston tool to allow the caliper to fit over the new brake pads.
    
17. 16 Slide the caliper over the brake pads and reinstall the caliper slide pins.
    
18. 17 Torque the caliper slide pins to the manufacturer's specifications.
    
19. 18 Replace the wheel on the vehicle and torque it down to manufacturer specifications located in your repair manual.
    
20. 19 Lift the vehicle off of the jack stand with the floor jack and remove the jack stands.
    
21. 20 Lower the vehicle to the ground and remove the floor jack.
    
22. 21 Press the brake pedal several times to pressurize the brake system before test driving the vehicle.
    
23. 22 Drive the vehicle, performing several hard stops to make certain the brakes are operating properly.
    

jQuery('.article ol .image').each(function(i,e){ var $this = jQuery(this); $this.find('img').error(function(){ jQuery(this).remove(); $this.remove(); }); });

Removal & Installation Front To Remove:

1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
2. Remove the tire and wheel assembly.
3. Install 2 wheel nuts to secure the rotor on the hub.
4. Remove the bottom brake caliper pin bolt.
5. Pivot the brake caliper body upward and secure out of the way. Do NOT disconnect the hydraulic brake flexible hose from the caliper.
6. Compress the piston back into the bore using a C-clamp. Figure of brake assembly with caliper raised showing brake pads in mounting bracket
   
   
7. Remove the inboard and outboard brake pads from the brake caliper bracket.

To Install:

1. Install the brake pad retainers and both brake pads into the caliper bracket.
2. Pivot the brake caliper down over the brake pads and into the brake caliper bracket. Insert the lower brake caliper pin bolt and torque bolt to 70 ft-lb. (95 Nm).
3. Reinstall the tire and wheel assembly.
4. Lower the vehicle.
5. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
6. Check the master cylinder level and add fluid as necessary.

Rear To Remove:
Rear disc pads R&I

1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
2. Remove the tire and wheel assembly.
3. Install 2 wheel nuts to secure the rotor on the hub.
4. Remove the upper caliper mounting bolt.
5. Pivot the caliper down to access the pads.
6. Remove the inboard and outboard pads from the caliper bracket.
7. Remove the brake pad clips from the caliper bracket.
8. Compress the piston back into the bore using a C-clamp and the old inner pad.

To Install:

1. Install new brake clips in the caliper bracket.
2. Install the inboard and outboard pads in the caliper bracket.
3. Pivot the caliper up over the pads.
4. Reinstall the upper mounting bolt and tighten to 32 ft. lbs. (44 Nm).
5. Remove the 2 wheel nuts securing the rotor.
6. Reinstall the tire and wheel assembly.
7. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
8. Check the master cylinder level and add fluid as necessary.

Disc Brake Pads for Suburban 1500 Removal & Installation Front To Remove:
Front caliper mounting bracket

1. Remove the cover on the master cylinder and siphon out 2/3 of the fluid. This step prevents spilling fluid when the piston is pushed back into the caliper bore.
2. Raise and support the vehicle safely.
3. Remove the wheel and tire assembly.
4. Compress the brake piston back into its bore using a C-clamp.
5. Remove the 2 caliper mounting bolts. Lift the caliper off the rotor.
6. Remove the inboard and outboard pad.
7. Remove and discard the anti-rattle clips.

To Install:
Caliper bracket sleeves

1. Thoroughly inspect, clean and lubricate all caliper slide points, bolts and hardware.
2. Install new anti-rattle clips.
3. Position the inboard and outboard pads into the support bracket
4. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
5. Install the caliper mounting bolts through the sleeves in the inboard caliper ears and into the mounting bracket.
6. Tighten the mounting bolts to: 80 lb. ft, (110 Nm).
7. Install the tire and wheel assembly. Lower the vehicle.
8. Add fluid to the master cylinder reservoirs so they are 1/4 in. (6.35mm) from the top.
9. Test the brake pedal by pumping it to obtain a hard pedal. Check the fluid level and add fluid as necessary.

Rear To Remove:

1. Remove 2/3 of the brake fluid from the master cylinder.
2. Raise and safely support the vehicle.
3. Remove the wheel and tire assembly.
4. Remove the brake caliper mounting bolts. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
5. Remove the brake pads from the caliper mounting bracket.
6. Remove and discard the anti-rattle clips.

Rear brake caliper

To Install:

1. Install new anti-rattle clips.
2. Position the brake pads to the caliper mounting bracket.
3. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
4. Install NEW caliper mounting bolts. Tighten to: 30 lb. ft, (40 Nm).
5. Install the wheel and tire assembly.
6. Lower the vehicle.
7. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly to seat the brake pads. Burnish the brakes as needed.

No,,,Remove the wheel,the brake caliper,unplug the abs sensor,if it is 4x4,rmove the center nut on the axle,rmove the rotor,and caliper braket,bracket first of course,then unbolt the three bolts that hold the bearing assembely,that is it.

There are two different types of calipers used on 01 Beetles.
The first which does not have a detachable caliper bracket is easiest and is as follows:
Remove front wheels
Unbolt calipers from integrated spindle/bracket with proper allen bit and lift calipers and pads and support them.
Remove set screw holding rotor to hub. You may need an impact screwdriver as these seize up with age.
Slide rotor off hub.

The second has a separate detachable bracket that wraps around the rotor.
Remove the front wheels
Remove two caliper bracket bolts holding bracket, caliper and pads onto rotor as a unit.
Some vehicles have a standard bolt in this position, some have a VW special star bolt, so inspect to see if you are equipped to remove these. If you have the star bolts and do not have the proper tool, you need to get it... attempting to use the wrong tool will not end well.
Use a philips screwdriver to remove the set screw holding the rotor to the hub. You may need an impact screwdriver as these screws seize up with age.
Slide rotor off the hub.

It should pull off, you may have to get a big "C" clamp and push the caliper piston back, or sometimes you can pry the piston back with a bar or screwdriver, be careful what you pry on.

First remove the cap off the master cylinder. Push in the piston on one caliper with a c clamp, or pry it back between the pad and rotor with a prybar. Then remove the 2 bolts on the caliper itself. Replace pads.Go to other side, repeat sequence