Question about Hyundai Cars & Trucks

1 Answer

My Hyundai Tucson 2005 model automatic, only moves in reverse gear and cannot engage on drive gears. Gear oil has been filled to capacity I am now confused somebody help.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 46 Answers

Shift solenoid, inside transmission

Posted on Jan 31, 2020

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Jonah Oneal

  • 14092 Answers

SOURCE: gear shift won't move out of park sometimes

look for transmission shift interlock solenoid fuse.or a bad brake switch will cause transmission not to come out of park.

Posted on May 16, 2009

Anonymous

  • 2 Answers

SOURCE: automatic transmission wont catch into any gear

You sould have been moore frequent on your transmission fluid changes, and you shouldn't have taken it to Jiffy Lube either. Your best bet is to drain and fill the trans fluid run it shift gears. Drain and fill again. Do this 3 times. Yeah the transmission fluid is expensive. on the last drain and fill you want to get a bottle of LUBE GUARD from NAPA or who ever sells it. put the whole 10oz bottle in. Shift Rev, 1, 2, 3, D. Neutral Rev D. If that don't work then you have bad seals.

Posted on May 27, 2009

ghost4548

Paul McGrath

  • 776 Answers

SOURCE: hyundai excel 1996 automatic will engage reverse

It appears you have a Forward Clutch FAILURE. Replace the trans after you get it diagnosed and verified by a professional technician. By the way, do you have a Check Engine light? If so, what is the diagnostic code? The dealership can scan the system and find any codes which may have been stored in the TCM (Transmission Control Module). If there were any 'Incorrect Gear Ratio" codes, it's most probably the trans itself.

Posted on May 28, 2009

ghost45

PAUL MC G

  • 1280 Answers

SOURCE: vehicle wont change up into gear reverse gear not

P0734 - 4th gear incorrect ratio. P1529 Malfunction Indicator Lamp Request. Problem is in the transmission.
Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Posted on Oct 03, 2009

ghost45

PAUL MC G

  • 1280 Answers

SOURCE: 2001 Hyundai - reverse gear is inoperative. The

If I understand you correctly, you have ALL forward gears working, but reverse doesn't?... then the problem is in the transmission itself or the linkage on the trans linkage into reverse.

Posted on Oct 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car stars normally, the gear selector moves to P D R, but when given gas the car remains still w/engine running and revving. Dash shows car is in Drive or Reverse.


try to remove the positive cable from the battery and wait for 5 minutes then install back the positive cable. start the engine and try to engages the gears again

Sep 02, 2015 | 2006 Hyundai Tucson

1 Answer

Why is the reverse Gear not working


you might want to use the recommended fluids sometimes its important to sounds like not running through the filter system right

Sep 23, 2014 | 2005 Hyundai Getz 1.6

1 Answer

Will not go into first gear when going down the gears


I will answer this as if it is a manual gear box as the solution will be different for an automatic.
First gear has a syncro ring energise spring that when pushed against the syncro cone in the gear spins the gear to the relevant shaft speed so that engagement is smooth. Because of the vast difference of the shaft speeds when engaging 1st gear the energising doesn't get a chance to work and so the gears refuse to mesh. To possible ways to get around this is to keep the road speed low say around 10mph or less or increase the engine rpm up to around 3500-4000rpm before trying to engage 1st gear. Basically the syncro is for engaging the gear as you are coming to a stop or going very slow . Check the drain plug magnet for metal as the clutch shaft bearing may be moving forward and preventing the engagement properly.

Apr 15, 2014 | 2005 Hyundai Tucson

1 Answer

Reverse stop plate problem?


IN the selector rails in the top section of the box there is a spring loaded de-dent ball that come into play when the lever is placed or pushed towards reverse. To select reverse you have to overcome this spring so that the selector rail can be moved. IF you can get a look at the top section of the box you may see a plug that is screwed in and facing the gear selector lever min the reverse position. If you can unscrew this plug there should be a spring and then a plunger of ball. I suspect that the spring may be broken or the plunger is stuck. If you can get to the gear lever pivot and remove it you will see the plunger that I am talking about . It should be in the removable top section

Nov 27, 2013 | 2006 Hyundai Tucson

2 Answers

How do I check transmission fluid levels on a tuscon


if its an automatic .there will be a dip stick near the front of the engine i think its got an orange ring pull if its a Manuel there is a hex bolt on the side of the gear box \[big enough to add fluid through a tube if you open it and clean fluid run out .then its enough .but if you open it and dirty fluid runs out then it requires changing .dont over fill .this will do more harm than good .its best to let a garage do it { a quick fit type place will do it for about 30 pounds }

Apr 02, 2011 | 2005 Hyundai Tucson

1 Answer

I have an automatic gas 2006 hyundai tucson. recently i noticed that when i engage the drive or reverse gear the vehicle lurches forward or backward accompanied by a banging noise. i have had both engine...


idle air control valve or iac same thing it controls idle speed yours is to high or you have a bad cv joint but i dnt think its that to new of car i would say your idle is to high

Apr 04, 2010 | 2006 Hyundai Tucson

1 Answer

2001 Hyundai - reverse gear is inoperative. The


If I understand you correctly, you have ALL forward gears working, but reverse doesn't?... then the problem is in the transmission itself or the linkage on the trans linkage into reverse.

Oct 18, 2009 | Hyundai Accent Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...