This could be a cracked/broken shifter tube is the shifter lever very loose and wiggling around then this is your problem, go to the bottom of the steering column and the shifter tube is connected to the cable you must grab the tube with pliers and turn it while someone or yourself turns the key to remove it the tube breaks from not stepping on the brake long enough and trying to force it out of park into drive before it releases and now there's a tab for the shift interlock solenoid and also the ignition switch rod that are not in the proper position to let you remove the key the rod from the cylinder is still in the applied position to start the truck because of the broken tube
This could be a cracked/broken shifter tube is the shifter lever very loose and wiggling around then this is your problem, go to the bottom of the steering column and the shifter tube is connected to the cable you must grab the tube with pliers and turn it while someone or yourself turns the key to remove it the tube breaks from not stepping on the brake long enough and trying to force it out of park into drive before it releases and now there's a tab for the shift interlock solenoid and also the ignition switch rod that are not in the proper position to let you remove the key the rod from the cylinder is still in the applied position to start the truck because of the broken tube
This could be a cracked/broken shifter tube is the shifter lever very loose and wiggling around then this is your problem, go to the bottom of the steering column and the shifter tube is connected to the cable you must grab the tube with pliers and turn it while someone or yourself turns the key to remove it the tube breaks from not stepping on the brake long enough and trying to force it out of park into drive before it releases and now there's a tab for the shift interlock solenoid and also the ignition switch rod that are not in the proper position to let you remove the key the rod from the cylinder is still in the applied position to start the truck because of the broken tube
×
Hi buddy,
Would suggest ya to try some online manuals.. if u know a good website then go ahead or otherwise try reliable-store.com
It's great for automobile repair and the people are also very helpful..
All the best:)
SOURCE: ignition
Sounds like the battery is dead, you have just enough power to have the lights come on, but no cranking of the starter. Try putting the battery on a trickle charger, or hook up jumper cables to another car which is running. Let it run with the jumper cables connected for two mintues before you try and start your car.
SOURCE: Starting
To find out if the key is bad go to local lock smith and ask for a code key from the vin number they will tell you you need a chip that is correct but the key will open the door and turn on the ignition. if the new key works then your key is bad and the dealer can make you one for about 100.00 dollars if it still dont turn then the key cylinder is bad and it will need to be replaced good luck
SOURCE: 2002 mercury cougar with key stuck in
it seems like you have a broken tumbler you should have a dealer or locksmith look at it
SOURCE: My key won't turn in the ignition. What dealer
If the key does not turn you need to replace the entire lock cylinder
SOURCE: 2010 corolla key stuck in ignition
It can be faulty ignition lock cylinder.I suggest to wiggle the steering wheel a bit and see if the key gets released out.If that is not helping then first turn steering wheel to right and try removing the key,or next turn steering wheel to left and see if you can remove the key. http://technoanswers.blogspot.in/2012/02/key-wont-turn-in-ignition-on-toyota.html ------------------- How to remove ignition switch on VW Car models? http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html -----------------
----------
Spray wd-40 in the ignition key hole and let it remain there for few minutes,after that once again try to remove the key and see if that helps.
---------
But if that is not helping then ignition lock cylinder has to be removed out and key has to be manually removed.
-----------
For more troubleshooting on these types of issues,i suggest you to refer the help links mentioned below.Its the accurate solutions mentioned in it.that will help you to narrow the problem:-----
Click the link below:------
-----------1999 Toyota Camry: Key Will Not Come Out Of
Ignition?
http://whatisbyme.blogspot.in/2012/05/1999-toyota-camry-key-will-not-come-out.html
---------------2001 Toyota Tacoma: Ignition Locked?
http://technoanswers.blogspot.in/2012/04/2001-toyota-tacoma-ignition-locked.html
------------Ignition Switch Will Not Turn Off?
http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html
-----------Car will not turn the ignition to start?
http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html
-----------
Ignition Key OFF but engine still running?
http://howtobyme.blogspot.in/2012/03/ignition-key-off-but-engine-still.html
--------------Chevrolet Malibu: Key Stuck in ON
position?
http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html2012 Dodge Ram: Ignition
Key will not release?
http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html-----------Ignition locked up on Mercury Villager?
http://technoanswers.blogspot.in/2012/01/ignition-locked-up-on-mercury-villager.html-------------Key won't turn in the ignition on Toyota land cruiser?
http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html
-------------How to Replace Ignition Switch on Chevrolet
Caprice Classic?
1995 Ford Taurus: Ignition switch not turning OFF?
http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html
-------------Ignition Problem Troubleshooting
http://whoisbyme.blogspot.in/2012/07/ignition-problem-troubleshooting.html
------------------These will help.Thanks.
607 views
Usually answered in minutes!
×