How do you repair trim pieces at joints in ceiling it looks like ceiling is falling

Fill them with caulk, the house is settling, there is no chance of the ceiling falling.

The issue being that over time thru vibration and such one of these solder joints will fail (happened on or 1999) you can repair this though. You will have to remove all of the trim from around the driver's side dash board, this will include the trim towards the center of the dash. Once these pieces are remove you'll need to remove the gauge panel (I believe (4) allen head screws) carefully bring the panel and release the wire clip from it. Looking at the back of the panel, where the plug was, carefully with plenty of light look for one of the pins to have a failed solder joint. It will be very faint however the failed joint will be a fine dark line around the pin. To correct use a small soldering iron and reheat this solder until it wants to flow, let it cool and reassemble.
I hope this may have helped,
Tom
PS: I have helped several persons with this issue, please review my profile; good luck with it (also often times with this issue the ABS light stays on)

There has been issues with the solder joints on the PIN connection to the gauge cluster. The issue being that over time thru vibration and such one of these solder joints will fail (happened on or 1999) you can repair this though. You will have to remove all of the trim from around the driver's side dash board, this will include the trim towards the center of the dash. Once these pieces are remove you'll need to remove the gauge panel (I believe (4) allen head screws) carefully bring the panel and release the wire clip from it. Looking at the back of the panel, where the plug was, carefully with plenty of light look for one of the pins to have a failed solder joint. It will be very faint however the failed joint will be a fine dark line around the pin. To correct use a small soldering iron and reheat this solder until it wants to flow, let it cool and reassemble.
I hope this may have helped,
Tom
PS: I have helped several persons with this issue, please review my profile; good luck with it (also often times with this issue the ABS light stays on)

This, I hope will repair this for you.

There has been issues with the solder joints on the PIN connection to the gauge cluster. The issue being that over time thru vibration and such one of these solder joints will fail (happened on or 1999) you can repair this though. You will have to remove all of the trim from around the driver's side dash board, this will include the trim towards the center of the dash. Once these pieces are remove you'll need to remove the gauge panel (I believe (4) allen head screws) carefully bring the panel and release the wire clip from it. Looking at the back of the panel, where the plug was, carefully with plenty of light look for one of the pins to have a failed solder joint. It will be very faint however the failed joint will be a fine dark line around the pin. To correct use a small soldering iron and reheat this solder until it wants to flow, let it cool and reassemble.
I hope this may have helped,
Tom
PS: I have helped several persons with this issue, please review my profile; good luck with it (also often times with this issue the ABS light stays on)

I expect the is should do it for you.

There has been issues with the solder joints on the PIN connection to the gauge cluster. The issue being that over time thru vibration and such one of these solder joints will fail (happened on or 1999) you can repair this though. You will have to remove all of the trim from around the driver's side dash board, this will include the trim towards the center of the dash. Once these pieces are remove you'll need to remove the gauge panel (I believe (4) allen head screws) carefully bring the panel and release the wire clip from it. Looking at the back of the panel, where the plug was, carefully with plenty of light look for one of the pins to have a failed solder joint. It will be very faint however the failed joint will be a fine dark line around the pin. To correct use a small soldering iron and reheat this solder until it wants to flow, let it cool and reassemble.
I hope this may have helped,
Tom
PS: I have helped several persons with this issue, please review my profile; good luck with it (also often times with this issue the ABS light stays on)

I expect the is should do it for you.

There has been issues with the solder joints on the PIN connection to the gauge cluster. The issue being that over time thru vibration and such one of these solder joints will fail (happened on or 1999) you can repair this though. You will have to remove all of the trim from around the driver's side dash board, this will include the trim towards the center of the dash. Once these pieces are remove you'll need to remove the gauge panel (I believe (4) allen head screws) carefully bring the panel and release the wire clip from it. Looking at the back of the panel, where the plug was, carefully with plenty of light look for one of the pins to have a failed solder joint. It will be very faint however the failed joint will be a fine dark line around the pin. To correct use a small soldering iron and reheat this solder until it wants to flow, let it cool and reassemble.
I hope this may have helped,
Tom
PS: I have helped several persons with this issue, please review my profile; good luck with it (also often times with this issue the ABS light stays on)

Sounds like a fuse for the instrument cluster OR the PCM.

There has been issues with the solder joints on the PIN connection to the gauge cluster. The issue being that over time thru vibration and such one of these solder joints will fail (happened on our 1999) you can repair this though. You will have to remove all of the trim from around the driver's side dash board, this will include the trim towards the center of the dash. Once these pieces are remove you'll need to remove the gauge panel (I believe (4) allen head screws) carefully bring the panel and release the wire clip from it. Looking at the back of the panel, where the plug was, carefully with plenty of light look for one of the pins to have a failed solder joint. It will be very faint however the failed joint will be a fine dark line around the pin. To correct use a small soldering iron and reheat this solder until it wants to flow, let it cool and reassemble.
I hope this may have helped,
Tom
PS: If you look at my profile you'll see this fix has worked for several others , good luck!

There has been issues with the solder joints on the PIN connection to the gauge cluster. The issue being that over time thru vibration and such one of these solder joints will fail (happened on or 1999) you can repair this though. You will have to remove all of the trim from around the driver's side dash board, this will include the trim towards the center of the dash. Once these pieces are remove you'll need to remove the gauge panel (I believe (4) allen head screws) carefully bring the panel and release the wire clip from it. Looking at the back of the panel, where the plug was, carefully with plenty of light look for one of the pins to have a failed solder joint. It will be very faint however the failed joint will be a fine dark line around the pin. To correct use a small soldering iron and reheat this solder until it wants to flow, let it cool and reassemble.
I hope this may have helped,
Tom

There has been issues with the solder joints on the PIN connection to the gauge cluster. The issue being that over time thru vibration and such one of these solder joints will fail (happened on our 1999) you can repair this though. You will have to remove all of the trim from around the driver's side dash board, this will include the trim towards the center of the dash. Once these pieces are remove you'll need to remove the gauge panel (I believe (4) allen head screws) carefully bring the panel and release the wire clip from it. Looking at the back of the panel, where the plug was, carefully with plenty of light look for one of the pins to have a failed solder joint. It will be very faint however the failed joint will be a fine dark line around the pin. To correct use a small soldering iron and reheat this solder until it wants to flow, let it cool and reassemble. Often times when these PIN connections fail the ABS light will illuminate; why I am incertain.
I hope this may have helped,
Tom
PS: If you check my profile you'll see I have helped others with this same issue, as I had to make this repair myself.