Question about Cars & Trucks

1 Answer

The bolt holding the blade on is stuck and I can’t undo it to get to the belt to replace it. Any tips on undo it?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,234 Answers

What are you working on? it would help fixya folks a lot with that info. Thanks

Posted on Apr 30, 2018


3 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



  • 125 Answers

SOURCE: I need to replace the tensioner belt pulley on my

I usually use a 3/8" breaker bar with a shallow well socket to get them out. They are typically hard to loosen but with the breaker bar it makes it easy.

Posted on Jan 05, 2010

anthony skidmore

  • 275 Answers

SOURCE: Himself has tried to replace the battery on the 03

If you are talking about the battery clamp bolts turning, then put a screwdriver in the split of the clamp and try to put turning pressure on the screwdriver and at the same time undo the nut of the clamp bolt. Or if you have a pair of mole grips, clamp the bolt head and undo the nut. Worst case , pry the clamp off the terminal and use a hacksaw and cut the bolt in half and remove it , fit a new bolt after. Hope that helps

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do u get the power steering pump out of a Buick rendezvous 06

Remove the drive belt,by loosening the adjuster,undo the pipes to the pump,undo the bolt ,s holding it to the motor,lift away and fit new one.You may have to remove other belts to get to the pump belt.

Oct 30, 2016 | 2006 Buick Rendezvous

1 Answer

How to replace rear-left seat belt?

un do the bolts that hold the seat belt rewinder
take out the back seat and then undo the bolt that holds seat belt to floor of car then install whole replacement seat belt unit inset and retighten the bolts.

Oct 13, 2015 | 2009 Toyota Camry LE

1 Answer

How long to replace alternator on 3.3L

Wrenches-- loosen bolts holding it in place, move it so belt comes loose. lift belt off pulley, undo bolts and remove alternator. use reverse process to install.

Oct 08, 2014 | 2005 Chrysler Town & Country

1 Answer

Need to replace ac compressor

you half to take the belt off then the alternator then the bracket that holds it on undo the top rad hose then undo the the lines to the compressor and un plug the wire's undo the 4 bolts and pule it out

Jul 30, 2012 | 2002 Ford Taurus

1 Answer

Can't undo nut on timing belt pully on 1986 gemini, Tried using starter motor while resting socket bar on solid support, no good, any suggestions

First, don't hold bar on cog as you will damage those and ruin it. Using the starter is a good way to damage starter or flywheel.

Soak the bolt with PB Blaster or WD40 and let is soak for a day. Use a large impact gun (3/4 or 1") with plenty of air flow and pressure.
If that does not work, then use a torch to heat the bolt head (not red hot or anything like that), then strike the bolt head straight on with a brass rod using a heavy hammer (32oz or so). This will break any corrosion that has welded the bolt head to the balancer.
Then use your wrenches again.
If that does not work, then try this: How to remove stuck harmonic balancer bolt

Feb 01, 2018 | Cars & Trucks

1 Answer

How to change belts on 2002 Nissan Frontier 4 cylinder

2002 frontier 4 cyl: 1) take off air intake tube, 2 screws 13 mm above radiator. 2) 1st belt for power stirring has pulley, undo pulley screw and unscrew adjuster bolt enough to take belt off 3) 2nd belt for alternator and water pump has no pulley but adjusting bolt and mounting bolt on alternator pulley, loosen mounting bolt and unscrew adjusting bolt enough to take belt off, if alternator will not move go under the truck and remove plastic cover- 6 screws 13 mm heads, after that look directly under alt. Pulley and should see a screw head 9/16 in, loosen it so alternator can move, now should be easy to remove belt ( it will be a lot harder to put new one though) 4) 3rd belt for compressor has pulley so follow #2 to remove it ,have to be done under the truck. First 2 belts will have to work around fan blades to remove them so wear gloves. After replacing belts remember that not to over tighten bolt on pulleys.

Jul 05, 2012 | 2002 Nissan Frontier Crew Cab

1 Answer

1995 toyota corolla passenger side window will not close stuck open

Replace window regulator and motor. Procedure: Remove inside door panel, cut regulator wires, raise window manually and hold in place, undo bolts holding window glass to regulator, undo bolts holding regulator to door-frame, remove regulator. Reverse to install.

Feb 11, 2010 | 1995 Toyota Corolla

2 Answers

Hi, could you please tell how to remove the bottom cover on a 1.6 vw bora......which is covering the bottom pulley for a timing belt change..... does the tensioner need to come off.....? and if so how do...

the one on the engine ?? two bolts either side ,cant remember but yes you may have to remove the fan belt tensioner thinking about it ,quick tip ?? to undo the bottom crank pulley bolt ,use a knuckle bar on socket and jam the knuckle bar into suspension then crank with starter motor ,undoes them everytime it does.Then before you slacken anything to do with the timing ,bring it around to TDC no 1 and paint all the pulleys to the block with white paint ,except the water pump and idlers .

Nov 10, 2009 | 2002 Volkswagen Golf

1 Answer

1985 Silver Spirit. Gates 7270 belt to smog pump. Will not go over fan blades. Which bolts to romove to remove fan?

hold fan belt with both hands as if stretching a rubber one end of belt over a fan blade all the way down to the hub.loop the other end over as many blades as length allows.''leap frog'' over remaining blades as necessary.if that doesn't do,there should be 4 bolts holding fan hub to it's mount on water pump spindle

Sep 26, 2009 | 2006 Rolls Royce Rolls Royce Silver Spirit

2 Answers

Need to take clutchfan off to replace waterpump

to take fanclutch off undo the big bolt, fanclutch will come off

Jan 27, 2009 | 2003 GMC Sierra 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides