Cars & Trucks Logo

Related Topics:

Spaceman 101 Posted on Apr 10, 2018

Where is modulator valve located on trans 1988 jeep comanche

5 Related Answers

Anonymous

  • 475 Answers
  • Posted on Nov 25, 2008

SOURCE: Break Lights won't come on in my 1988 Jeep Comanche

Why replace the whole fuse box? That's rediculous. If you can't find the fuse box, just fix the affected circuit. Did they check the brake switch?

Ad

Anonymous

  • 118 Answers
  • Posted on Jan 30, 2009

SOURCE: 1988 jeep wrangle

Check your spark plugs. Without good spark plugs the ignition won't ignite. Just go look for Jeep spark plugs at like AutoZone and they are real cheap. To change them you will need a long socket wrench to twist them out and change each one.

Anonymous

  • 5 Answers
  • Posted on Sep 11, 2009

SOURCE: location of fuel pump relay

should be under the hood on the drivers side

simidrm45844

  • 159 Answers
  • Posted on Sep 27, 2009

SOURCE: need wiring diagram for 1988 jeep comanche 4x4 6

check the solenoid on the starter it powers the ign for starting then switches to run when you let off key,either the solenoid is bad or a wire to the solenoid has come unhooked and sometime they have an in line fuse which can blow.

jamie

  • 1810 Answers
  • Posted on Jan 13, 2010

SOURCE: 1988 Jeep Comanche transmission will not shift automatically

chapters and indago sell chilton books they are a god send the have all the wiring diagrams in the back of the book also auto zone carries the books too

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Rear brakes lock when press brake pedal.

get is serviced.

its stuck in , low bed (loaded) mode. the lever is or parts in side

stuck in full load mode.

and guess what, if you bypass the valve, what will happen

the rear brake will lock, going fast and if on wet or worse roads. 10x worse. its there for a reason. to lower the brake pressure with no pickup bed load. or not heavy trailer tongue weight.



ever consider the rear brakes are bad. first. and not the valve.



service the rear shoes and slaves.

then check the bypass.



Does the truck still have the height sensing brake line bracket and line connected into the prop valve?



http://www.jeepforum.com/forum/f53/bad-proportioning-valve-any-ideas-1127468/#post10505224







here is the valve.

sold at , JEEP.



http://www.factorychryslerparts.com/products/JEEP/1988/COMANCHE/VALVE--Proportioning--VALVE--Proportioning--ECE-198789--1989--Except-France--Italy--1990--KDX--KDX-After-3-1-93--KDX-Up-to-3-1-93/4520728/52009114.html



Chysler p/n

52009114 ; 52003118



google that and find them for $75
1helpful
1answer

1988 jeep comanche brake proportioning valve

there only 2 ways (USA answers)
they have a guage test (expensive gauge)
or replace it ,if in fact you know for sure the rear brakes are good.

i think raybestos sells this.valve rebuilt.

the valve is height measuring disconnect the link and see if its
free? is it jammed? i had a 88 from new.
i purged brake fluid every year and it lasted for 250k miles. and sold it.
so there is a bench mark on life.(best case)
did you read the fsm? yet
id does cover these tests.

try alldata.com (usa ) it may cover Commanche.
0helpful
1answer

1988 jeep comanche not shifting properly stays in first gear, any ideas???

what size engine/ transmission is in your jeep? have you checked the fluid level with it running? have any recent repairs been done?was the jeep wrecked recently? if you can give me a good idea of what led up to it not shifting i can most likely find the problem.
0helpful
1answer

Where is the slave cylinder on a 1988 Jeep comanche

I'm assuming you're referring to the clutch slave cylinder... It is located on the input shaft to the transmission. You'll need to separate the ****** from the engine in order to access it.
0helpful
1answer

Location of horn on 1988 jeep comanche 2x4

the very front of the jwwp on the driver side onder the headlights you'll might need to remove it
0helpful
1answer

1988 Jeep Comanche transmission will not shift automatically

chapters and indago sell chilton books they are a god send the have all the wiring diagrams in the back of the book also auto zone carries the books too
0helpful
1answer

When i start my 1988 jeep comanche the tail light fuse blows

change the amp. of the fuse it should be higher than the former fuse you use.
1helpful
1answer

Need diagram of vacuum system for 1988 jeep comanche pick-up 6 cy

Haynes manual has a diagram. Main important hookups are to power brake booster, fuel pressure regulator and map sensor. also need a connection to a/c controls inside drivers compartment and evap system canister. will also need connection to egr valve solenoid if you have one. as well as pcv on valve cover (or ccv which replaces pcv on some)
Not finding what you are looking for?

62 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...