2005 Taurus SE. What are inner tie rod torque specs?

Question edited for clarity, MAKER.
Question moved to model category.

Torque spec question : 2000-2005 (other than GXP)

http://www.pontiacbonnevilleclub.com > topic52656
Jul 4, 2020 · 4 posts · 3 authors
Stabilizer bar link nut 13 ft.lbs. Strut mount nut 55 ft.lbs. Strut mount to body 35 ft.lbs. Strut to knuckle 135 ft. lbs.
2000 Torque Specs : Specifications and General Information
1 post
May 21, 2008
Quick Torque Specs Question : 2000-2005 (other than ...
2 posts
Sept 27, 2014
stupidly over done topic but need some questions answered
6 posts
Jun 17, 2016
Broken spring : 2000-2005 (other than GXP)
6 posts
May 19, 2019
More results from www.pontiacbonnevilleclub.com

2004 bonneville se: steering..torque specs for tie rod..strut..bolts

https://www.justanswer.com > ... > Pontiac Problems
Jun 22, 2010 - lbs.) Strut Mount to Body Nut, 47 Nm (35 ft. lbs.) Strut to Knuckle Nut, 147 Nm (108 ft.
1 answer · Top answer: Tie Rod Inner to Gear 100 Nm (74 ft. lbs.)Tie Rod (Front) Lock Nut 64 Nm

27 ft lbs

https://www.instructables.com/Replacing-an-Outside-Tie-Rod-on-a-Honda-CRV/

What are the torque specs for the rod bearings on a 2006 - Fixya

https://www.fixya.com > ... > 2006 Dodge Caravan
Nov 15, 2019 - What is the torque specification for the inner tie rod 1996 .dodge caravan 2.4 liter. 45-55 foot pounds. Read full answer. Sep 18, 2012 • 1998 ...
SOLVED: Torque chart for dodge caravan 4l - Fixya
Sept 9, 2019
Main bearing torque spec for Dodge Grand Caravan 2005
Sept 15, 2019
Im trying to find the connector rod bearing torque - Dodge - Fixya
Jul 15, 2018
Head bolt torque specs for 2.4L dohc dodge caravan - Fixya
Jun 2, 2012
More results from www.fixya.com

Dodge Caravan 2.4 need engine tightening specs and head ...

https://www.justanswer.com > chrysler > 28qv6-dodge-...
Jun 27, 2009 - SPECIFICATIONS - TORQUE ; Balance Shaft Carrier Cover-Bolts, 12, - ; Camshaft Sprocket-Bolt, 101, 75 ; Connecting Rod Cap-Bolts, 27 +¼ turn, 20 +¼ ...
1 answer · Top answer: Here are the head bolt specs: Before installing the bolts, the threads should be coated with ...

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3
PDF
Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. CASE. 2.4. 148. 61-66. 45-50 FT/LBS. 90-100 FT/LBS. 60-65 FT/LBS. CASE. 2.4.
124 pages
You've visited this page 3 times. Last visit: 01/02/22

Here is the inner tie rod end specs

Tighten the inner tie rod to 100 N.m (74 lb ft).

you can get guide from many sites.. i know few
like reliable-store
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete refurbish, repair, installation every single thing is covered
within seconds u can get the access and it's totally illustrative complete

not enough info year make and model

59 ftlbs

Hope this will answer your question,If do pls click on helful botton and you can follow me at fixya,so I can answer your question faster.thanks.

Here are the tie rod end nut torque specs:
• Lower Control Arms - (Front and Rear bolt) 129 ft-lbs x2 and (Knuckle Stud) 37 ft-lbs
• Upper Control Arms - (Front and Rear bolt) 140 ft-lbs x2 and (Knuckle Stud) 37 ft-lbs
• Inner Tie Rods - 81 ft-lbs
• Outer Tie Rods - (Knuckle Stud) Tie Rod nut 44 ft-lbs and jam nut 55 ft-lbs
• Stabilizer Links - 17 ft-lbs
• Rear Shocks - Lower and Upper 85 ft-lbs
• Front Shocks - Module Bolt x2 37 ft-lbs, Module nut x3 37 ft-lbs and Stud nut 37 ft-lbs

Exact same thing happened to me. On my 03 taurus and 03 Windstar. It ended up be worn inner tie rod ends. Would reccommend an inspection of bushings, tie rods etc.

45 Ft-lbs Tie-rod balljoint stud-to-steering knuckle nut, and 55 Ft-lbs Tie-rod (outer)- to- inner jam lock nut