97 Golf,lock/unlock button inoperative and must use key to enter passenger door. Hatchback is locked and cannot be unlocked with key. Driver's door key does unlock passenger door and hatchback. Is a fuse or relay?

Does your fusion have Power Door Locks - Without Memory or Power Door Locks - With Memory ? Do you know about ford SJB - smart junction box ?

Power Door Locks - Without Memory
Regardless of the key position, the smart junction box (SJB) is supplied voltage at all times. When the SJB receives a signal from the remote keyless entry (RKE) transmitter, the keyless entry keypad, or the door lock control switches, the SJB supplies a ground signal to the appropriate lock or unlock relay. The ground signal closes the relay which supplies voltage to the door lock actuators. The door lock actuators then actuate to a lock or unlock position.
Power Door Locks - With Memory
Regardless of the key position, the SJB and the driver door module (DDM) are supplied voltage at all times. When the SJB receives a signal from the RKE transmitter, the keyless entry keypad, or either door lock control switch, the SJB sends a command to the DDM, through the controller area network (CAN), and a ground signal to the lock and unlock relays. When the LH door lock control switch is pressed, the DDM receives the lock or unlock signal. The DDM will send a request through the CAN network to the SJB to lock or unlock the passenger doors. The SJB then responds to the DDM request, authorizing a lock or unlock of the driver door by the DDM. The DDM then supplies voltage and ground to the driver door lock actuator based on the lock or unlock request. The ground signal in the SJB closes the relay which supplies voltage to the remaining door lock actuators. The remaining door lock actuators then actuate to a lock or unlock position determined by the relay.

• A single or all passenger door locks are inoperative - with memory

• Circuitry
• Door lock actuator (part of the door latch)
• DDM
• SJB

• Go To Pinpoint Test A .

• A single or all passenger door locks are inoperative - without memory

• Circuitry
• Door lock actuator (part of the door latch)
• SJB

• Go To Pinpoint Test B .

Important: If all 3 passenger door locks are inoperative from both door lock switches, test the unlock control circuit between the splice and the BCM for an open.? Do you know how to do this ? Looking at a wiring diagram an using a DMM - digital multi-meter ?
Free wiring diagrams here http://www.bbbind.com/free-tsb , enter vehicle info. year , make , model an engine size . under system click on body & accessories , then under subsystem click on power locks . Click search button then the blue link . Or maybe your best bet mite be to take it to a qualified repair shop. You would need factory service repair info. to find splice location .

Power Door Locks Inoperative - Passenger Door
Step
Action
Yes
No
Schematic Reference: Door Lock/Indicator Schematics
Connector End View Reference: Vehicle Access Connector End Views
DEFINITION: One or all 3 of the passenger door lock actuators do not operate, or, the front passenger door lock switch does not operate.
1
Did you perform the Diagnostic System Check - Vehicle?
Go to Step 2
Go to Diagnostic System Check - Vehicle
2
Verify that the Power Door Locks Inoperative - Passenger Door fault is present.
Do the door locks operate as described in Power Door Locks Description and Operation ?
Go to Testing for Intermittent Conditions and Poor Connections
Go to Step 3
3
Are all 3 of the passenger doors locks inoperative from both door lock switches?
Go to Step 10
Go to Step 4
4
Install a scan tool.
Close all of the vehicle doors.
With the scan tool, observe the Right Front (RF) Door Lock Switch parameter in the Data Display, Inputs list of the body control module (BCM).
Operate the front passenger door lock switch to both the LOCK and UNLOCK positions.
Did the parameter change to both the LOCK and UNLOCK states?
Go to Step 7
Go to Step 5
5
Important: If the 3-amp fuse of the jumper wire opens when the jumper wire is connected, test the appropriate signal circuit for a short to battery positive voltage.
Disconnect the harness connector of the front passenger door lock switch.
Connect a 3-amp fused jumper wire between the lock switch lock signal circuit of the harness connector and a ground.
Observe the RF Door Lock Switch parameter.
Connect the 3-amp fused jumper wire between the lock switch unlock signal circuit of the harness connector and a ground.
Observe the RF Door Lock Switch parameter.
Did the Scan Tool parameter change to the both the LOCK and UNLOCK states?
Go to Step 6
Go to Step 8
6
Connect the 3-amp fused jumper wire between the lock switch lock signal circuit and the ground circuit of the harness connector while observing the appropriate Scan Tool parameter.
Did the Scan Tool parameter change to the LOCK state?
Go to Step 11
Go to Step 14
7
Disconnect the harness connector of the inoperative door lock actuator.
Connect a test lamp between the door lock actuator lock control circuit and the door lock actuator unlock control circuit of the harness connector.
Operate the front passenger door lock switch to the LOCK and UNLOCK positions.
Did the test lamp illuminate in both positions?
Go to Step 13
Go to Step 9
8
Test the signal circuits of the front passenger door lock switch for a short to ground or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 18
Go to Step 12
9
Test the lock control circuit of the inoperative door lock actuator for an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 18
Go to Step 10
10
Important: If all 3 passenger door locks are inoperative from both door lock switches, test the unlock control circuit between the splice and the BCM for an open.
Test the unlock control circuit of the inoperative door lock actuator for an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 18
Go to Step 12
11
Inspect for poor connections at the harness connector of the front passenger door lock switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 18
Go to Step 15
12
Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 18
Go to Step 16
13
Inspect for poor connections at the harness connector of the inoperative door lock actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 18
Go to Step 17
14
Repair the open ground circuit of the front passenger door lock switch. Refer to Circuit Testing and Wiring Repairs .
Did you complete the repair?
Go to Step 18
--
15
Replace the front passenger door lock switch. Refer to Front Side Door Lock Replacement .
Did you complete the replacement?
Go to Step 18
--
16
Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?
Go to Step 18
--
17
Replace the inoperative door lock actuator. Refer to Front Side Door Lock Actuator Replacement
Did you complete the replacement?
Go to Step 18
--
18
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

The locks on your vehicle are electronically controlled by the BCM - body control module . The driver an passenger door switche's are input's to the BCM . Do you know anything about automotive electronic's ? anti theft alarm remote, could this be part of the problem , No it's just a key less entry remote , nothing to do with the anti-theft .
Door Lock System Components
The Power Door Lock System consists of the following components:
• Body control module (BCM)
• Driver door lock switch
• Front passenger door lock switch
• Door lock actuators in each of the doors
• IBCM (PWR) 15-amp fuse

Door Lock System Controls
The Power Door Lock System is controlled by the body control module (BCM) and can be activated by any one of the following:
• A door lock switch Lock or Unlock actuation
• A keyless entry transmitter actuation
• An automatic door lock actuation
• An automatic door unlock actuation
• A last door closed locking (LDCL) actuation

Driver and Passenger Door Unlock Operation w/o Keyless Entry
When the body control module (BCM) detects a transition of either of the door lock switches to the Unlock position, it switches the door lock actuator unlock control circuits to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the driver passenger door lock actuators transition to the Unlock position.

Your best bet , take your vehicle to a qualified repair shop ! Need special tool to diagnose .

Power Door Locks Inoperative

Install a scan tool.
Turn ON the ignition, with the engine OFF.
With a scan tool, observe the door lock switch parameter in the Doors data list.
Does the scan tool display Idle?
YES - Go to Step 4
NO - Go to Step 8
4
Activate the driver door lock switch to the LOCK and UNLOCK positions.
Does the scan tool display Idle?
YES - Go to Step 9
NO - Go to Step 5
5
Activate the front passenger door lock switch to the LOCK and UNLOCK positions.
Does the scan tool display Idle?
YES - Go to Step 9
NO - Go to Step 6
6
With a scan tool, observe the driver door lock actuator command and the passenger door lock actuator command parameters in the Doors data list.
Activate a door lock switch to the LOCK and UNLOCK positions.

Year make and model. You may have a inoperative door lock actuator.

stick key in driver door lock and unlock it. If that works, now see if the remote will unlock the door or doors..i remember reading in an owners manual once where you can program which doors open and close by they way you press and hold down the two main buttons, also after a battery change in the remote, i think, but not sure, i did this on a blazar i once owned... the owners manual said, that you had to be within 20 feet and press and hold down both buttons till it makes the arming sound.... Can i get some feedback cause im curious..thanks.

Synchronization
When
Key buttons operated repeatedly while vehicle out of range and system becomes inoperative.
How
Polo: Press key unlock button for approximately 1 second. Golf/Bora: Press key lock or unlock button for approximately 1 second. Manually lock or unlock vehicle. System should now lock or unlock vehicle. If not, carry out programming procedure.
Programming
When
Key added or replaced. System malfunction.
How - Polo
Keys can only be programmed using diagnostic equipment.
NOTE: A maximum of 4 keys can be programmed.
How - Golf/Bora
98MY
Keys can only be programmed using diagnostic equipment.
NOTE: A maximum of 4 keys can be programmed.
How - Golf/Bora 99MY


Switch ignition ON. Insert key to be programmed into driver's door lock. Lock vehicle manually. Press lock or unlock button. Wait at least 1 second. Press lock or unlock button again. Vehicle horn sounds to indicate correct programming. Keys can also be programmed using diagnostic equipment.
NOTE: A maximum of 4 keys can be programmed.

Maybe fuse number 6 is blown (check lefthand side of steerning wheel where all teh fuses are located - you must open the door)

wires go thru the boot. most likely broken wire from the switch. if the window works with the key in the door

Sounds like bad wiring, or bad door lock actuators. Check for power while locking/unlocking the doors.

1997 ford explorer awd child safety won't open from the inside can you help