2003 Honda CR-V Logo

Related Topics:

Abakus Posted on Mar 11, 2017

I need to change a 03 honda crv cam sensor. Where is it located and is it an easy fix?

5 Related Answers

mtous2162

  • 58 Answers
  • Posted on Jun 04, 2009

SOURCE: 2002 honda crv air filter change

Hi!

Can you specify if you are referring to the engine intake air filter or the cabin air filter?
If you are referencing the cabin air filter, the attached youtube video should help.

I originally created the video for the Odyssey, but found out after looking at my dad's CRV that it is essentially the same procedure as the Odyssey, and have also noticed that the same stands true for most Honda vehicles built between 2005 and 2009.

Happy motoring!

Ad

LOS COMPUTER REPAIR

  • 27 Answers
  • Posted on Jul 01, 2009

SOURCE: WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA

WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

scottyoung56

Scott Young

  • 91 Answers
  • Posted on Aug 30, 2009

SOURCE: speed sensor volvo s70 1998. Is this an easy fix?

it is on the back side of the roter and yes it is easy to fix and no there is on special tools just undo the two bolts pull it off unpluge it and then put the new one on and have a good day

Testimonial: "Direct answer to a direct question. Replaced the paret in 5 mins. Thanks"

Jerry Parmanand

  • 449 Answers
  • Posted on Nov 17, 2009

SOURCE: location of Idle control valve on 04 CRV

It's not a easy job but I'm pretty sure you had one of those problems where the idle surges if this is the case take out the air intake tube that leads to the throttle body, get a can of carburetor fluid and spray around the throttle body. You will need someone to start the car and hold the gas peddle to 2500 rpm while you do this the car will shut of when you do this, restart the car and repeat the process until half of the can is used up. Now check your antifreeze level fill if needed and reset you check engine light. Now you can take the idle air back and get your money.

Anonymous

  • 1 Answer
  • Posted on Oct 31, 2011

SOURCE: where is the fuel filter located honda crv 2002

The filter is attached to the top of the fuel pump. It can be accessed by pulling back the carpet in the rear storage area and removing an access panel

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

1998 Honda CRV. Where is o2 sensor on it?

On a V6 engine, bank 1 is on the drivers side or the bank closest to the firewall. Sensor 1 is the one in the exhaust manifold BEFORE the catalytic converter and sensor 2 is just after in the cat on the way to the tail pipe. On a 4 cylinder engine, there are only two sensors, before (1) and (2) after the Cat.

https://www.google.com/search?q=1998+honda+crv+oxygen+sensor+Bank+1+Sensor+2+location

Buy Denso OEM (original equipment manufacturer) sensors, don't go cheap on Mexico of China copies.

https://www.google.com/search?q=1998+honda+crv+oxygen+sensor

..
0helpful
1answer

Location of crankshaft sensor on 2000 HONDA crv

the dealer pages show it as
Sensor Crank Tdc
37500-P72-A01 ID # 11
AT CRANK FRONT, HAS TONE WHEEL.

https://www.hondapartsonline.net/v-2000-honda-cr-v--ex--2-0l-l4-gas/engine--oil-pump-oil-strainer

I BET THE BELT SLIPPED (ALL DO, THAT) 60 TO 100K MILES
AND when slipped timing is wrong, cam and crank.
cam timing is first thing to address if will not start, no spark and no fuel. and compression 1/2 normal
0helpful
2answers

How do i change the fuel filter on a 2003 honda crv

Newer vehicles have fuel fileter in the gas tank, IF you are not geting any fuel, try replacing the cam position sensor.
1helpful
1answer

Knock sensor(bank 2) are there 2 Knock sensors on a 2003 CRV? Computer saying no signal from knock sensor bank 2.

I looked 03 honda crv, 2.4L engine. A four cylinder only has one bank. I looked at wiring diagram, it only showed one knock sensor. Hope this helps. It appears to be left of starter motor. If picture is incorrect, my bad.
knock sensor-hxuqwykuqyqpp0zswssgq0zl-1-0.jpg
1helpful
1answer

The location of the camshaft censor on a HONDA C.R.V 1999

There is no dedicated cam sensor on these devices. The cam position is sensed by the electronics in the distributor.
0helpful
1answer

Where is the camshaft sensor located on a 2005 honda crv

on end of the cam.
no engine stated of the many options, so ......?????
nor why you ask.
DTCs?
what?
login to
alldata.com and read. its all there.
0helpful
1answer

My Honda CRV fails to start every now and again. This has happened three times in the last year? I`ve changed the spark plugs but this made no difference and the problem remains.

this is most likly your fuel pump relay its located under driver side dash half the size of a pack of smokes easy 65 dallor fix
7helpful
2answers

HONDA CR-V

OK, you have a code PO341 which means their is a problem with the signal the ECU is receiving from the cam sensor. It does not necessarily mean the sensor is bad. It can be one of these things.
1. Cam sensor wiring routed too close to spark plug wiring (causing interference) 2. Poor wiring connection at cam sensor 3. Poor wiring connection at PCM 4. Bad cam sensor 5. Damaged reluctor wheel You replaced the cam sensor and the problem is still there so we can assume that a defective cam sensor was not the problem. Do this.
1. Check that the wiring isn't routed too close to any secondary ignition components (coil, spark plug wires, etc.) 2. Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing 3. Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage 4. If reluctor isn't visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design)
Not finding what you are looking for?

339 views

Ask a Question

Usually answered in minutes!

Top Honda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...