Were is the safety neutral switch located on my 2001 ford Taurus and how much to change part

SOURCE: Location of NSS(neutral safety switch) on 2002 Dodge Caravan

It is in side the trans on top of the valve body. Why do you think you need to replace it?

Marvin

• 85242 Answers
• Posted on Jun 15, 2009

SOURCE: Neutral Safety Switch Location

on the transmission where the shift cable attaches.

SOURCE: Where is the neutral safety switch located on 1998 Town & Country

THE NEITRAL SAFTEY IS LOCATED ON THE DRIVERS SIDE OF THE TRANSMISSION WHERE THE SHIFTING LINKAGE HOOKS TO AN ELECTRICAL SWITCH THIS SWITCH CONTROLS ALL FUNCTIONS
REVERSE LTS, NEUTRAL SAFETY AND OTHER ITEMS

ZJ Limited

• 17989 Answers
• Posted on Sep 18, 2009

SOURCE: Looking for the neutral safety switch

Neutral Safety/Back-up Light Switch

This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.

C6 Transmission



C6 neutral start switch

1. Disconnect the negative battery cable.
2. Raise and safely support the vehicle on jackstands.
3. Remove the downshift linkage rod return spring at the low-reverse servo cover.
4. Coat the outer lever attaching nut with penetrating oil. Remove the nut and lever.
5. Remove the 2 switch attaching bolts, disconnect the wiring at the connectors and remove the switch.
6. Installation is the reverse of removal. Adjust the switch and tighten the bolts to 55-75 inch lbs. (6.2-8.5 Nm).
7. Remove the jackstands and lower the vehicle.
8. Connect the negative battery cable.

1. Disconnect the negative battery cable.
2. Raise and safely support the vehicle on jackstands.
3. Disconnect the wiring from the switch.
4. Using a deep socket, unscrew the switch.
5. Installation is the reverse of removal. Tighten the switch to 10 ft. lbs. (14 Nm).
6. Remove the jackstands and lower the vehicle.
7. Connect the negative battery cable.

1. Disconnect the negative battery cable.
2. Raise and safely support the vehicle on jackstands.
3. Disengage the harness connector from the MLP sensor.
4. Remove the 2 sensor attaching bolts and remove the sensor.

1. Install the MLP sensor and install retaining bolts. Do not tighten, the sensor requires adjustment.
2. Adjust the MLP sensor then tighten attaching screws to 80-100 inch lbs. (9-11 Nm).
3. Remove the jackstands and lower the vehicle.
4. Connect the negative battery cable.

1. Hold the steering column transmission selector lever against the Neutral stop.
2. Move the sliding block assembly on the neutral switch to the Neutral position and insert a 0.091 in. (2.3mm) gauge pin in the alignment hole on the terminal side of the switch.
3. Move the switch assembly housing so that the sliding block contacts the actuating pin lever. Secure the switch to the outer tube of the steering column and remove the gauge pin.
4. Check the operation of the switch. The engine should only start in Neutral and Park .

1. Position the manual control lever in Neutral .
2. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
3. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
4. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).

ZJ Limited

• 17989 Answers
• Posted on May 07, 2010

SOURCE: where is the location neutral safety switch on

2001 Mazda Truck MPV 2WD 2.5L MFI 6cyl
The neutral saftey switch is on the front of trans. To remove, unscrew the four screws that hold up the plastic cover, remove it then look at front of tran it will be right there.it will have the shifter cable attatached to it. Loosen the bolt an make shure to put the van in nuetral there will be a small hole at the top of the shifting nob put a small brill bit through the hole an through the saftey switch this will aline the two an should start.

Good luck (remember rated this post).