Honda 40th anniversary accord 2009 Whole front end installation Bumper, grille, headlight ect...
SOURCE: Where & how to install thermostat in honda accord ex 1992
you need to follow the upper hose that lead from the radiator to the engine, there is two bolt that connect the thermostat housing to the block loosen the bolt using a 10 mm socket with ra-chet. Make sure that the engine is cool off before attempt to do this you will lose coolant but that's ok you will add the coolant when you finish replacing the thermostat. start the engine with the radiator cap off then add coolant slowly and cap it, then fill the reservoir up.
note the way you remove the thermostat that's the same way you will put the new one so pay attention when you remove the old one good luck.
SOURCE: Bumper cover removal
It is a little more complicated than that. There are two nuts below the headlight assemblies in the engine compartment. You will need to remove the battery and overflow bottle to get at the one on the passenger side. Remove the turn signals in the bumper, then there are 2 or 3 bolts holding a mounting bracket behind the each of the turn signals. There are a number of bolts with washer heads and reatiners on the underside of the bumper as the previous responder indicated.
SOURCE: 2005 Honda Accord Front Bumper cover replacement
easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time
SOURCE: How to change the whole headlight assembly on a 05 Honda CRV
You have to remove the front bumper and grill etc
There are 5 bolts holding the headlight assembly in place. 2 at the top and 3 underneath.
Remove the plastic cross piece by prising out the clips and then the grille clips too then unbolt the bolts eithr side under the wheel arch. The bumper is still fastened using cips. Pull the bumper forward to unclip.
SOURCE: how to install a front bumper for a 1996 Honda accord sedan
Installation of a front bumper can be
complicated. These helpful instructions may help a person with this
task. If you choose to install a bumper yourself, please be cautioned
that professional installation is always recommended. Please confirm
before you start that your safety equipment has been applied to you,
your car and your new bumper. These 10 easy steps can make a difficult
install relatively easy.
The following steps are detailed instructions that you can follow. It
is very important that you make sure to read each step carefully and
completely:
1. Look closely at the new bumper and your car for screws, bolts and
clips. Remove these pieces from your existing front bumper and place
them in a safe area. Follow this by the full removal of the cars current
front bumper.
2. Next, test the fit of the new front bumper. Make sure that nothing
hinders with the placement and fit on the car.
3. If the fitment is correct the installation process may move
forward.
4. If the fitment is incorrect then the removal or repositioning of
certain components, such as reinforcement bars may be required. This is
because every car is different. If this is the case remove the element
and test fit the front bumper again. This should be done with caution
and is done at the installers own risk.
5. Most of the time the new aftermarket bumper is placed the exact
way the factory piece was. The most important key to great fitment in
installation is the drilling procedure. The holes should be drilled in
the places that will give the piece a great fit. Usually, these holes
will be drilled in the same place as the factory bumper. At this point
only mocking is required.
6. When the bumper is in place, shaving or filing maybe required.
Many parts will require this because certain areas are made with more
material to lower the risk of damage. Also, if a car has been in an
accident or previously modified, this may cause additional sanding,
cutting or filing.
7. Now that the front fits well, be very precise and drill the holes.
8. Prepping for paint is what needs to be done after the holes have
been drilled. Depending on what material the front bumper is made of
will determine the steps for prepping.
9. After the piece has been painted, clear coating may be
appropriate.
10. Make sure there are not any leftover parts and that everything is
secure. After this is done, your front bumper installation
process is complete.
344 views
Usually answered in minutes!
×