What size is the lower adjusting bolt on the alternator & can the fan belt be easily adjusted

adjust ur belt by following steps
now that you know where the components are these components are driven by a belt. So when you turn your AC on there’s a belt that’s driving the AC compressor, when you turn the stirring wheel and you have that nice that easy feel of turning the stirring wheel when you’re parallel parking your car that’s the power stirring pump doing its job. Your alternator is keeping the battery charged, the lights on and the engine running. So I want to show you where the belts are, what they look like, how to adjust them and how to tell a bad belt from a good belt. As you can see these are your drive belts, this is the AC drive belt it drives the AC compressor, this is the alternator drive belt it drives the alternator, if you look down here you can see this is where the adjustment is on that AC compressor belt, if you look right here this is the top adjusting bolt for adjusting the alternator either up or down to tighten or loosen the belt. There’s a bolt down here that locks the alternator in place and this bolt is the pivot bolt for the alternator. So if you’re going to let’s say remove your alternator belt you’d have to remove these covers, loosen this bolt, loosen this bolt that’s underneath this cover and adjust this bolt to either lower the alternator or raise the alternator, if you’re belt was too loose you’ll pull up on the alternator, if the belt was too tight you’ll

ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.

REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt

Fig. Loosen the adjuster lock bolt . . .

Fig. . . . then remove the alternator belt from the engine

1. Loosen the alternator support nut.
2. Loosen the adjuster lock bolt.
3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
4. Remove the belt.

To install:

1. Install the belt on the pulleys.
2. Rotate the adjuster bolt clockwise until the proper tension is reached.
3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .

Fig. . . . then remove the power steering belt from the engine

1. Remove the alternator belt as described above.
2. Loosen the power steering pump adjusting bolts.
3. Remove the power steering pump fixed bolt on the rear of the bracket.
4. Rotate the pump toward the engine and remove the belt.

To install:

1. Install the belt on the pulleys.
2. Rotate the pump until the proper tension is reached.
3. Tighten the adjusting bolts on the pump.
4. Tighten the fixed bolt on the rear of the bracket.
5. Install the alternator belt.

A/C COMPRESSOR BELT

1. Loosen the tension pulley and remove the belt.
2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

1. Disconnect the negative battery cable.

CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.

1. Raise and safely support the vehicle and remove the front undercover.
2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
3. Remove the belt.

To install:

1. Install the belt on the crankshaft and alternator pulleys.
2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
3. Tighten the fixing nut to hold the adjustment.
4. Install the undercover and lower the vehicle to the floor.
5. Connect the negative battery cable.

POWER STEERING BELT

1. Disconnect the negative battery cable.

CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.

1. Raise and safely support the vehicle and remove the undercover.
2. Remove the alternator and A/C compressor belt.
3. Lower the vehicle and remove the cruise control pump link assembly.
4. Place the power steering hose under the oil reservoir.
5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:

1. Install the power steering pump drive belt.
2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
3. Tighten the fixing bolts.
4. Raise the vehicle and install the alternator and A/C compressor belt.
5. Install the undercover and lower the vehicle.
6. Connect the negative battery cable.

3.0L SOHC Diamante

1. Disconnect the negative battery cable.
2. Loosen the lockbolt on the face of the A/C tensioner pulley.
3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
4. Remove the A/C compressor belt.
5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
7. Remove the power steering/alternator belt.

To install:

1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

• TESTING
• REMOVAL & INSTALLATION

Alternator

Print

TESTING

The easiest way to test the performance of the alternator is to perform a regulated voltage test.

1. Start the engine and allow it to reach operating temperature.
2. Connect a voltmeter between the positive and negative terminals of the battery.
3. Voltage should be 14.1-14.7 volts.
4. If voltage is higher or lower than specification, connect a voltmeter between the battery positive (B+) voltage output terminal of the alternator and a good engine ground.
5. Voltage should be 14.1-14.7 volts.
6. If voltage is still out of specification, a problem exists in the alternator or voltage regulator.
7. If voltage is now within specification, a problem exists in the wiring to the battery or in the battery itself.

Many automotive parts stores have alternator bench testers available for use by customers. An alternator bench test is the most definite way to determine the condition of your alternator.

REMOVAL & INSTALLATION

1993-94 Models
See Figures 1 through 5

1. Disconnect the negative battery cable, for safety purposes.
2. Remove the right side splash guard from under the vehicle.
3. Disconnect the alternator lead wires and connections. Label them if you are unsure of their locations.

Fig. Fig. 1: The large positive lead connection is protected by a rubber boot

Fig. Fig. 2: Make sure the alternator ground wire is also removed

1. Loosen the drive belt adjusting bolt and slip the belt off the pulley.
2. Remove the lower adjustment bolt, followed by the upper pivot bolt.

Fig. Fig. 3: Remove the lower adjustment bolt ...

Fig. Fig. 4: ... followed by the upper pivot bolt. Make sure you support the alternator

1. Lower the alternator from the vehicle.

To install:

1. Using a C-clamp and a socket, push the upper pivot bushing back in it's bore until it bottoms out.

Fig. Fig. 5: Using a C-clamp to push in the pivot bushing will make installation easier

1. Raise the alternator into the engine bracket, and push the upper pivot bolt all the way through the bracket to support it.
2. Install the lower adjustment bolt, followed by the upper pivot nut.
3. Place the belt on the alternator pulley, and tighten the belt.
4. Tighten the upper and lower mounting bolts.
5. Engage the alternator lead wires and connections.
6. Connect the negative battery cable.
7. Start the vehicle, and check for proper operation.
8. Readjust the belt tension, if necessary. Install the lower splash guard.

1995-98 Models

1. Disconnect the negative battery terminal.
2. Remove the splash guard on the right side of the vehicle.
3. Loosen the alternator belt idler pulley.
4. Slip the drive belt off the alternator pulley.
5. Remove the four air conditioning compressor mounting bolts.
6. Remove the radiator fan and fan shroud.
7. Move the air conditioning compressor forward.
8. Disconnect the alternator harness connector.
9. Remove the alternator mounting bolts, and lower the alternator from the vehicle.

To install:

1. Hold the alternator in place and install the mounting bolts.
2. Plug in the alternator harness connector.
3. Move the air conditioning compressor back into location.
4. Install the radiator cooling fan and shroud.
5. Install the air conditioning compressor mounting bolts.
6. Place the drive belt on the alternator pulley.
7. Tighten the drive belt to the proper tension with the idler pulley.
8. Install the splash guard.
9. Connect the negative battery terminal.

Proper belt tension is important. A belt that is too tight may cause alternator bearing failure; one that is too loose will cause a gradual battery discharge and/or belt slippage, resulting in belt breakage from overheating.

FIRST TURN OFF RADIO THEN DISCONNECT NEGATIVE BATTERY CABLE.IF YOU HAVE 2.7L ENGINE YOU HAVE TO REMOVE LOWER PLASTIC SPLASH SHIELD, REMOVE TRANSMISSION COOLER AND POSITION IT ASIDE.LOWER RADIATOR CROSSMEMBER SUPPORT, LOOSEN DONT REMOVE,ADJUSTING T BOLT AND THE PIVOT BOLT LOOSEN BELT ADJUSTING BOLT, REMOVE DRIVE. REMOVE ALTERNATOR FIELD CIRCUIT PLUG. REMOVE ALTERNATOR BATTERY PLUS TERMINAL NUT AND WIRE REMOVE.PIVOT BOLT SPACER CAREFUL DONT DROP LOSE SPACER. THEN REMOVE ALTERNATOR. YOU NEED BELT TENSION GAUGE TORQUE ADJUSTING T BOLT UNTIL TENSION GAUGE READS 120 LBS USED BELT NEW BELT 180 - 200 LBS. YOU NEED ALL BASIC MECHANIC TOOL SET WITH METRIC SOCKETS METRIC OPEN BOX END WRENCHES.SIZE WRENCH RANGE 5MM UP TO 19MM NEED ADJUSTABLE PLIERS NEED SCREW DRIVERS LIKE FLAT HEAD AND PHILLIPS. YOU NEED TORQUE WRENCH. FOR THE PIVOT BOLT NEED TORQUE TO 40 FT LBS. THE 8MM MOUNTING BOLT TO 30 FT LBS. 10MM BOLT TO 40 FT LBS.

V-BELT ADJUSTMENT CAUTION
On models equipped with an electric cooling fan, disconnect the negative battery cable or fan motor wiring harness connector before replacing or adjusting drive belts. The fan may come on, under certain circumstances, even though the ignition is OFF. Alternator Drive Belt

1. Position a ruler perpendicular to the drive belt at its longest run. Test the tightness of the belt by pressing it firmly with your thumb. The deflection should not exceed 1?4 in. (6mm).
2. If the deflection exceeds 1?4 in. (6mm), loosen the alternator mounting and adjusting arm bolts.
3. On 1968-72 V8 and 6 cylinder models, use a prytool to move the alternator toward or away from the engine until the proper tension is reached. NOTE: Apply tension to the front of the alternator only. Positioning the prytool against the rear end housing will damage the alternator.
   
4. On 1973 and later V8 models, place a 1 in. (25.4mm) open-end or equivalent wrench on the adjusting arm bolt and pull on the wrench until the proper tension is achieved.
5. Holding the alternator in place, tighten the adjusting arm bolt. Inspect the belt tension. When the belt is properly tensioned, tighten the alternator mounting bolt. Fig. 1: Alternator belt adjustment
   

Power Steering Drive Belt ALL 6-CYLINDER AND 1971-72 V8 MODELS

1. Holding a ruler perpendicular to the drive belt at its longest run, test the tightness of the belt by pressing it firmly with your thumb. The deflection should not exceed 1?4 in. (6mm).
2. To adjust the belt tension, loosen the adjusting and mounting bolts on the front face of the steering pump cover plate (hub side).
3. Using a prytool on the pump hub, move the power steering pump toward or away from the engine until the proper tension is reached. Do not pry against the reservoir as it is relatively soft and easily deformed.
4. Hold the pump in place, tighten the adjusting arm bolt and then inspect the belt tension. When the belt is properly tensioned tighten the mounting bolts.

1973 AND LATER V8 MODELS

1. Position a ruler perpendicular to the drive belt at its longest run. Test the tightness of the belt by pressing it firmly with your thumb. The deflection should be about 1?4 in. (6mm).
2. To adjust the belt tension, loosen the three bolts in the three elongated adjusting slots at the power steering pump attaching bracket.
3. Turn the steering pump drive belt adjusting nut as required until the proper deflection is obtained. Turning the adjusting nut clockwise will increase tension and decrease deflection; counterclockwise will decrease tension and increase deflection.
4. Without disturbing the pump, tighten the three attaching bolts. Fig. 2: Power steering belt adjustment (slider type)
   

Air Conditioning Compressor Drive Belt

1. Position a ruler perpendicular to the drive belt at its longest run. Test the tightness of the belt by pressing it firmly with your thumb. The deflection should not exceed 1?4 in. (6mm).
2. If the engine is equipped with an idler pulley, loosen the idler pulley adjusting boot, insert a prytool between the pulley and the engine (or in the idler pulley adjusting slot), and adjust the tension accordingly. If the engine is not equipped with an idler pulley, the alternator must be moved to adjust, as outlined under Alternator Drive Belt.
3. When the proper tension is reached, tighten the idler pulley adjusting bolt (if so equipped) or the alternator adjusting and mounting bolts. Fig. 3: Air conditioning belt adjustment
   

Thermactor® Air Pump Drive Belt

1. Position a ruler perpendicular to the drive belt at its longest run. Test the tightness of the belt by pressing it firmly with your thumb. The deflection should be about 1?4 in. (6mm).
2. To adjust the belt tension, loosen the adjusting arm bolt slightly. If necessary, also loosen the mounting belt slightly.
3. Using a prytool, pry against the pump rear cover to move the pump toward or away from the engine as necessary. WARNING
   Do not pry against the pump housing itself, as damage to the housing may result.
   
4. Holding the pump in place, tighten the adjusting arm bolt and recheck the tension. When the belt is properly tensioned, tighten the mounting bolt. Fig. 4: Air pump adjustment points
   

FOR THE 3.0L ENGINE IF YOU REPLACE AC BELT LOOSEN TOP IDLER PULLEY CENTER BOLT. IF YOU REPLACING ALTERNATOR AND WATER PUMP BELT LOOSEN ALTERNATOR ADJUSTMENT BOLT AND PIVOT BOLT.IF REPLACING POWER STEERING PUMP BELT LOOSEN POWER STEERING PUMP ADJUSTMENT BOLT AND MOUNTING BOLTS.****** FOR THE 2.4L ENGINE TO REMOVE POWER STEERING BELT LOOSEN TOP IDLER PULLEY.FOR ALTERNATOR AND WATER PUMP BELT LOOSEN ALTERNATOR ADJUSTER BOLT, PIVOT AND MOUNTING BOLTS.FOR AC COMPRESSOR LOOSEN LOWER IDLER PULLEY.

Timing Belt Removal & Installation SOHC To Remove:

1. Disconnect battery negative cable.
2. Remove fresh air duct.
3. Drain engine coolant into an appropriate container and retighten radiator drain plug.
4. Remove upper radiator hose.
5. Remove fan clutch assembly bolts.
6. Remove 5 cooling fan shroud bolts.
7. Remove fan shroud and fan as an assembly.
8. Loosen alternator mounting bolts and remove drive belt from pulley.
9. Remove fan pulley.
10. Remove 4 cooling fan assembly bolts.
11. Remove cooling fan assembly.
12. Remove 4 bolts and upper timing belt cover.
13. Remove 2 lower bolts and lower timing belt cover.
14. Loosen adjusting bolt and remove A/C belt.
15. Remove alternator belt.
16. Loosen power steering pump lock bolt and mounting bolt.
17. Remove drive belt from crankshaft damper. Camshaft timing marks
    
    
18. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
19. Remove 5 bolts and remove damper.
20. Remove timing belt guide from timing belt pulley.
21. Loosen tensioner lock bolt.
22. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt. NOTE: Mark the direction of timing belt rotation on the belt if it is being reused.
    
23. Remove timing belt.

To Install:
Timing belt pulley timing marks

NOTE: Timing belt pulley timing mark and timing mark must be aligned.
Camshaft timing marks

NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
Timing belt installation

1. Install timing belt with minimal slack from timing belt pulley to water pump and from water pump to camshaft pulley.
2. Loosen tensioner lock bolt until tension is applied to timing belt. CAUTION
   Do not turn crankshaft counterclockwise.
   
3. Turn crankshaft pulley 2 full turns clockwise and ensure timing marks are properly aligned.
4. Tighten tensioner lock bolt to 33 ft lb (45 Nm).
5. Apply a force of 21 lb to timing belt midway between idler pulley and camshaft pulley.
   • Deflection should measure 0.43-0.51 inch (11-13 mm)
   NOTE: if timing belt deflection is incorrect remove timing belt and install NEW tensioner spring.
   
6. Install timing belt guide.
7. Install crankshaft damper pulley.
8. Install 5 crankshaft damper pulley bolts. Tighten bolts to 132 in lb (15 Nm).
9. Install power steering pump drive belt.
10. Adjust power steering pump drive belt tension and tighten lock bolt and mounting bolt.
11. Install alternator drive belt.
12. Install A/C drive belt.
13. Install lower timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
14. Install upper timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
15. Install cooling fan assembly and 4 bolts. Tighten bolts to 27 ft lb (37 Nm).
16. Install fan pulley.
17. Install fan clutch and shroud as an assembly. Tighten bolts to 74 in lb (8 Nm).
18. Tighten 4 cooling fan nuts to 16 ft lb (22 Nm).
19. Adjust alternator belt tension and tighten alternator mounting bolts.
20. Install upper radiator hose.
21. Install fresh air duct.
22. Connect battery negative cable.
23. Refill/bleed cooling system.

DOHC To Remove:

1. Disconnect battery negative cable.
2. Remove fresh air duct.
3. Remove 5 cooling fan shroud bolts and 4 thermo-modulated fan nuts.
4. Remove 4 thermo-modulated fan shroud fasteners.
5. Remove generator drive belt.
6. Remove fan pulley (located above crankshaft pulley).
7. Remove 4 bolts and splash shield (located under front of vehicle).
8. Remove A/C drive belt and power steering drive belt. Timing Belt Removal
   
   
9. Remove 5 bolts and upper timing belt cover.
10. Remove 2 bolts and lower timing belt cover.
11. Loosen tensioner lock bolt and pivot tensioner pulley outboard.
12. Retighten tensioner lock bolt. NOTE: Mark timing belt for rotation if it is being reused.
    
13. Remove timing belt.

To Install:
Crankshaft match marks

1. Align marks on timing belt pulley and pump body. Camshaft pulley alignment marks
   
   
2. Align marks on camshaft pulleys with alignment marks on seal plate.
3. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
   
4. Loosen tensioner lock bolt.
5. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
6. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
7. Apply a force of 22 lbs to timing belt between camshaft sprockets.
   • Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
   NOTE: Replace tensioner spring if timing belt deflection is excessive.
   Timing Belt Installation
   
   
8. Install lower timing belt cover.
9. Install upper timing belt cover.
10. Install power steering drive belt and adjust belt tension.
11. Install fan pulley.
12. Install generator drive belt and adjust belt tension.
13. Install A/C drive belt and adjust belt tension.
14. Install splash guard.
15. Install fan and fan shroud.
16. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
17. Install fan shroud mounting bolts.
18. Install fresh air duct.
19. Connect hose to resonance chamber.
20. Connect battery negative cable.

I'm going to assume you have the 4WD model..here are the instructions for removal and install:

1. Drain the cooling system.
2. Remove or disconnect the following:
   
   Negative battery cable Lower splash shield Upper and lower radiator hoses Coolant reservoir tank hose Fresh air duct Fan and shroud Loosen the alternator mounting and adjusting bolts Alternator belt Fan pulley and bracket Upper and lower timing belt covers and turn the crankshaft until No. 1 cylinder is at Top Dead Center (TDC). Loosen the tensioner lockbolt and pry the tensioner away from the belt Timing belt Loosen the tensioner bolt Water pump Tensioners from the water pump

To Install:

1. Clean the surface of any old gasket material.
2. Install or connect the following:
   
   Tensioners on the water pump Water pump and gasket. Torque the bolts to 19 ft. lbs. 25 Nm). Timing belt Loosen the tensioner lockbolt and allow the tensioner to rest against the belt. Torque the tensioner lockbolt to 32 ft. lbs. (43 Nm). Upper and lower timing belt covers Fan bracket assembly and fan pulley Drive belt Cooling fan and shroud Position the radiator and torque the bracket bolts to 89 inch lbs. (10 Nm). Torque the shroud bolts to 89 inch lbs. (10 Nm) and torque the alternator adjusting and mounting bolts Position the fresh air duct over the radiator and tighten the retaining bolt 89 inch lbs. (10 Nm) Radiator hoses and tighten the clamps Lower splash shield Negative battery cable
   
3. Fill the cooling system.
4. Start the vehicle and bring the engine to operating temperature. Check for leaks and repair if necessary.

REMOVAL & INSTALLATION

See Figures 1 and 2


Fig. Fig. 1: Rear terminal alternator


Fig. Fig. 2: Side terminal alternator

1. Open the hood and disconnect the battery ground cable.
2. Remove the adjusting arm bolt.
3. Remove the alternator through-bolt. Remove the drive belt from the alternator pulley and lower the alternator.

Some engines are equipped with a ribbed, K-section belt and automatic tensioner. A special tool must be made to remove the tension from the tensioner arm. Loosen the idler pulley pivot and adjuster bolts before using the tool. See the accompanying illustration for tool details.

1. Label all of the leads to the alternator so that you can install them correctly and disconnect the leads from the alternator.
2. Remove the alternator from the vehicle.
3. To install, reverse the above procedure. Torque the pivot bolt to 58 ft. lbs.; the adjusting bolt to 25 ft. lbs.; the wire terminal nuts to 60-90 inch lbs.

BELT TENSION ADJUSTMENT

The fan belt drives the alternator and water pump. If the belt is too loose, it will slip and the alternator will not be able to produce it rated current. Also, the water pump will not operate efficiently and the engine could overheat.
Check the tension of the belt by pushing your thumb down on the longest span of the belt, midway between the pulleys. Belt deflection should be approximately 1 / 2 inch; (13mm).To adjust the belt tension, proceed as follows:

1. Loosen the alternator mounting bolt and the adjusting arm bolts.
2. Apply pressure on the alternator front housing only, moving the alternator away from the engine to tighten the belt. Do not apply pressure to the rear of the cast aluminum housing of an alternator; damage to the housing could result.
3. Tighten the alternator mounting bolt and the adjusting arm bolts when the correct tension is reached.