What is the torque setting for a front hub wheel bearing nut on a Toyota Quantum

1995 C1500 spindle nut torque procedure? - CK5 Network

https://ck5.com > ... > General Discussion > The Garage
Jan 31, 2005 - while rotating the hub in a foward direction torque the nut to about 12ft lbs. Keep doing that a few times to ensure the bearings are seated.

96 gmc: torque..the front spindle nut..C1500 - JustAnswer

https://www.justanswer.com > Car Questions > GM Repair
Sept 16, 2011 - Torque nut (12) 10-12 ft lbs while turning the wheel assembly forward by hand. This will seat the bearing. Loosen nut (12) to a just loose ...
1 answer · Top answer: You can attach the magnetic base to the end of the spindle or to the brake caliper bracket. ...

• 
  

  1996 chevy: the torque setting for front wheel bearing..1500 4x4

  https://www.justanswer.com > chevy > 1tv6x-1996-che...
  Feb 18, 2009 - Outer Tie Rod Nut (C and K Models) · Shackle to Frame Nut and Bolt (C3500HD) · Shock Absorber Nuts (K Models) ; 62 N·m · 95 N·m · 90 N·m ; 46 lb ft.

Torque specification guide - PDF4PRO

https://pdf4pro.com > cdn > torque-specification-...
PDF
Front and rear axle nut torque specifications for FWD, RWD and 4 W/D vehicles. Torque specification guide. Form #457377. April, 2007.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

Honestly you should search google. It is right there. the inner hub nut must be torqued to 59 Nm rotate the hub three times in each direction and then loosen the inner hub nut until it can be turned by hand, then again tighten the inner hub nut to 25 Nm. the lockwasher against the inner hub nut, it only goes in one way, it has a small inner tab that locates with the key way of the hub, this is between the threads. Once the lock washer is in the correct position, you can now install the outer hub nut, this outer nut must be torqued to 47 Nm, once you have tightened this outer nut, please once again check that the starting effort is correct.

Three bolts are 70 lbs,could be 120+/-.

Hello, here is the torque spec for front hub bearing
Strut to Steering Knuckle Bolt and Nut
180 N·m
133 lb ft
Tie Rod Retention Nut
50 N·m
37 lb ft
Wheel Bearing/Hub Mounting Bolt
130 N·m
96 lb ft
Wheel Drive Shaft Spindle Nut
205 N·m
157 lb ft

Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Lubricate the threads on the halfshaft with clean engine oil.
3. Remove or disconnect the following:
   • Front wheels
   • Halfshaft hub nut
   • Caliper from the steering knuckle WARNING
     DO NOT allow the brake hose to support the weight of the caliper.
     
   • Brake rotor
   • Anti-lock Brake System (ABS) sensor from the backing plate
   • Hub and bearing assembly from the backing plate
   • Hub and bearing assembly from the halfshaft
   • Hub and bearing assembly

To Install:
Exploded view of the front hub mounting and related components

1. Install or connect the following:
   • Hub and bearing assembly onto the halfshaft
   • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
   • ABS sensor
   • Brake rotor
   • Caliper on the steering knuckle.
   • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
   • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

you will need a big socket to remove the axle nut--about 20 mm or so. Other than that, I don't think so. Procedures from autozone.com below. it doesn't mention having to press bearing into hub.

Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   
   Front wheels Hub nut Brake caliper Rotor ABS sensor Wheel hub from steering knuckle and driveshaft Wheel bearings
   

To install:

1. Install or connect the following:
   
   Wheel bearing into hub Wheel hub to steering knuckle and driveshaft; torque bolts to 41 ft. lbs. (56 Nm) ABS sensor; torque to 6 ft. lbs. (8 Nm) Brake rotor and caliper New flanged hub nut; torque to 134 ft. lbs. (182 Nm)
   

Front (4 Wheel Drive) To Remove:

1. Raise and support the vehicle
2. Remove or disconnect the following:
   • Tire and wheel assembly
   • Rotor (See: Disc Brake Rotor)
   • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
   • Electrical connection for the wheel speed sensor
   • Front drive halfshaft assembly (See: Halfshaft)
   • Hub and bearing assembly mounting bolts 4WD front hub
     
     
   • Hub and bearing assembly

To Install:

1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
3. Install or connect the following:
   • Hub and bearing assembly
   • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
   • Front drive halfshaft assembly (See: Halfshaft)
   • Electrical connection for the wheel speed sensor
   • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
   • Rotor (See: Disc Brake Rotor
   • Tire and wheel assembly
   Wheel lug nut tightening sequence
   
   
4. Torque the lug nuts to specification
5. Test drive the vehicle to confirm the repairs

About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.

1. Disconnect the negative battery cable.
   
2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
   
3. Raise and safely support the vehicle. Remove the wheel.
   
4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
   
1. Remove the front brake rotor from the hub/bearing assembly.
   
2. Remove the retaining nut and washer from the halfshaft stub axle.
   
3. Remove the ABS wheel speed sensor from the steering knuckle.
   
4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
   
5. Remove the hub and bearing assembly from the steering knuckle.
   
5. To install:
   
   1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
      
   2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
      
   3. Install the disc brake rotor.
      
   4. Install the brake caliper assembly onto the steering knuckle.
      
   5. Install the axle washer and nut. Tighten but do not torque.
      
   6. Install the ABS wheel speed sensor.
      
   7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
      
   8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
      
   9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
      
   10. Reconnect the negative battery cable. Check the wheel alignment.
       

The hub/bearing assembly is attached to the steering knuckle with four bolts



Removing a hub/bearing assembly




If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind




The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

112 to 174 ft lbs