I need to change the pitarm in a dodge intrepid
SOURCE: my 96 Dodge intrepid needs
well that depends on a number of things. can you ndescribe what led you to believe that you though you needed motor mounts and carriage bushings? it would help a great deal if you could elaberate so i can give you the best solution.
SOURCE: replace spark plugs 2004 dodge intrepid
__________________
Changing Spark Plugs
First off, on this model you don't have plug wires, you have coil packs with a boot and coil connected to the pack. The boot slides on the tops of the spark plug. The good thing about this is that you don't have to mark each wire to its location.
So to replace the plugs you need to disconnect the electrical connector to the coil pack and then unbolt the two bolts that mount the pack down, then remove the pack.
Next with a ratchet, an extension and a special spark plug socket, which has an insulator inside to protect the porcelain from getting cracked, remove the spark plugs.
Next step is to replace the plug, usually I slide off the boot from the coil pack and then remove the coil from inside the boot and slide the boot over the spark plug and start to thread the plug back in. Using this method allows to you feel if you are threading the plug in right. Then with a torque wrench you would torque the spark plug to the specs for the type of engine you have.
3.2/3.5L Engine (20 ft-lbs)
2.7L Engine (13 ft-lbs)
Next reinstall the coil pack with the two mounting bolts, it is only necessary to hand tigthen the two bolts. Then plug back in the electrical connector and continue this process on the next 5 spark plugs.
__________________
Changing Dome Light
To remove the map light bulbs you need to first remove the overhead console.
To do this you need to remove the screw at the front of the overhead console (which is more towards the front windshield).
Next you need to pry down on the rear of the overhead console and then disconnect the electrical connectors.
Then, with the overhead console pulled down, pull of the map light bulbholders and replace the bulbs.
Installation is the reverse of the removal process.
SOURCE: I need to remove the upper intake manifold from my
First off, you need to label all of the electrical and vacuum lines connecting to the intake manifold. This will make reassembly much easier. Then, there is a torque sequence to be used during disassembly and reassembly.
This image is of the TIGHTENING SEQUENCE. Reverse this to take the manifold off. This is important so that the upper intake manifold is not warped at all, which would decrease the quality of the seal. Be careful during disassembly and reassembly to avoid bending any lines or tubes. If things are in your way, disconnect them rather than pushing them to the side. This will avoid pinching inner linings which cannot be seen visually.
As for the gaskets, (as far as I am aware), Chrysler's (Dodge's) official stance on the manifold gaskets is that they are reusable. However, this is if they ALL look good under close inspection. Any tears, "melting", or other damage means the gaskets should all be replaced. They are not expensive, and I believe they all come as a set including both upper and lower gasket sets. Personally, I would recommend replacing them regardless. This would be a good preventative step to help extend the life of the vehicle. Also be sure to check the cooling line O-rings and replace them as necessary, following the criteria above.
Good luck and I hope this helps, even though I see it is a bit late.
SOURCE: 2003 Dodge Durango clunking noise in front end can
With the information given this is not a sure solution. Questions that need to be asked is when does this happen, turning at slow speedm high speed, when hitting a pot hole etc? Since you have replaced a lot of things already, assuming you have NEW good quality parts so you did not replace bad parts with new bad parts i would definitelu check the pitman arm. This runs from the stering gear to the tierod. It can give you some good clunks while steering, especially at low speed when there is a lot of resistance. Check it by having someone turning the steering wheel when watchin/feeling it.
SOURCE: how do I change the back speakers in my 2004 Dodge
on my 03 there is a lining on the under side of the rear deck in the trunk with 3 tabs. pull them off and you'll see 2 hooks for the rear deck cover. the speakers are more then likely right under there,mounted from the top inside.
57 views
Usually answered in minutes!
×